Search:

Type: Posts; User: myshop1044; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds; generated 9 minute(s) ago.

  1. Replies
    7
    Views
    249

    I am using 3.103 and the import a tracing image...

    I am using 3.103 and the import a tracing image is a add on package, I have them for a while.
  2. Replies
    7
    Views
    249

    If you have “ import to trace “ , take a picture...

    If you have “ import to trace “ , take a picture as square as you can, imported, trace the outline and then you can cutout them very easily, here is a sample I did to recreate a saw handle. I did a...
  3. Replies
    9
    Views
    411

    Table rock

    What version of software are you using, if I open the mpc in 3.1? And saved it and you are using a lesser version, then you can open it.
  4. Replies
    9
    Views
    411

    I agree about the spacing, I didn’t have much...

    I agree about the spacing, I didn’t have much time to work with it, if we have “ variable draft” , we could do some fine tuning too
  5. Replies
    9
    Views
    411

    here is my idea, I like draft and lower height...

    here is my idea, I like draft and lower height allittle just me version
  6. Replies
    2
    Views
    144

    was this the one skeeterman, nice to hear from...

    was this the one skeeterman, nice to hear from you again
  7. Replies
    6
    Views
    1,119

    I have a set you may want to try, one vector and...

    I have a set you may want to try, one vector and one raster, picked this up sometimes back
  8. Replies
    4
    Views
    180

    Yes I did try .125 and it looked good, still...

    Yes I did try .125 and it looked good, still playing, thanks Ocsar
  9. Replies
    4
    Views
    180

    I played around with a different pic and created...

    I played around with a different pic and created this, 1/4” depth and not sure to use 1/16” or 1/32” bit, looks good so far.
    The size could about 8” x 12”
  10. Replies
    4
    Views
    180

    looking for a pattern

    I have a jumping horse pattern, but I was looking for one in this form a young lady, the pic quality is poor but any help would be great
  11. Thread: CutOut

    by myshop1044
    Replies
    7
    Views
    281

    Glad to help

    Glad to help
  12. Thread: CutOut

    by myshop1044
    Replies
    7
    Views
    281

    This somewhat more difficult, first draw the arc...

    This somewhat more difficult, first draw the arc first, then with “ connected line tool” you trace over the rosette with many line sections until you reach the other end of the arc. Turn on cutpath,...
  13. Replies
    6
    Views
    364

    yes I have 2 of Floyd's first versions dust...

    yes I have 2 of Floyd's first versions dust collectors , and a 1500cfm dust collector system next to the CWS, the problem with cast acrylic , it flakes and is hot and stick to everything.
  14. Replies
    6
    Views
    364

    I used a 1/2” straight cut trim bit, on a 3/16”...

    I used a 1/2” straight cut trim bit, on a 3/16” test board, 1/16” pass each time, then I switched to 1/4” cast acrylic for the finish product, even with duct collector on , it looked like it snowed...
  15. Thread: CutOut

    by myshop1044
    Replies
    7
    Views
    281

    See attached, select a 1/2” grid, snap to grid,...

    See attached, select a 1/2” grid, snap to grid, draw the arc and the outside corner, this creates a region, select cutpath, flip to the outside and accept, next mirror all four corners and do a...
  16. Replies
    7
    Views
    296

    Do you use a stop collar on your bits, this...

    Do you use a stop collar on your bits, this ensures the correct depth when you insert the bits in
  17. Replies
    14
    Views
    703

    Very nice quality oscarl48

    Very nice quality oscarl48
  18. Replies
    19
    Views
    884

    Yes it was a peacock and the eyes on the tail had...

    Yes it was a peacock and the eyes on the tail had different colors for the different layers
  19. Replies
    19
    Views
    884

    Years ago someone showed some multi color layered...

    Years ago someone showed some multi color layered plywood, haven’t seen it since , !!!
  20. Replies
    3
    Views
    218

    Is the lexan clear without the paper off, if so ,...

    Is the lexan clear without the paper off, if so , it maybe seeing thru the Lexan and trying to reach the bottom of the sled.
    I use white litho material witch reflects the light, just a thought.
  21. Thread: World Globe

    by myshop1044
    Replies
    3
    Views
    390

    I have hundreds old patterns, if you need...

    I have hundreds old patterns, if you need anything just let me know
    Perry B.
  22. Thread: World Globe

    by myshop1044
    Replies
    3
    Views
    390

    will this work for you

    will this work for you
  23. Replies
    12
    Views
    571

    Sharon will this help, I highlighted all the text...

    Sharon will this help, I highlighted all the text and raised the height btwn the lines to a max of 100 and this is how it appears.
  24. Replies
    3
    Views
    442

    Thanks DianMayfield, for the link, I looked all...

    Thanks DianMayfield, for the link, I looked all over my projects and couldn’t find my version, oh well.
    back then it looked like Star Wars, now the pads come with the stand ready to go.
    thanks again
  25. Replies
    3
    Views
    442

    Just for the old CW folks

    Let’s go way back to 2013, I found these pictures on IPad holder I made, but don’t have a layout or I’m not sure how I did it.
    Does any of you old folks remember this and has a layout or patterns....
Results 1 to 25 of 499
Page 1 of 20 1 2 3 4