Search:

Type: Posts; User: cestout; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    5
    Views
    16,441

    I need a 3D file for WWII ruptured duck

    Customer wants a door plaque, but I can't find a pattern or a file to make a pattern. Could buy a lapel pin but they are too small to scan.
    thanks
    Clint
  2. Does the bit plate snap out and does the bit...

    Does the bit plate snap out and does the bit touch near the center of the bit plate. I net, find out why. Usual problem, reach in the back corner over the cut motor and make sure the wires from the...
  3. Replies
    6
    Views
    1,760

    Connie, piercing had to be available because...

    Connie, piercing had to be available because there is a place to check it. I put a carved region under the hinge parts .6 deep - It is carved.25+ from the back - and that cleared it. I was just...
  4. Replies
    6
    Views
    1,760

    3.106 works as it should. 1.187 and 1.188 don't....

    3.106 works as it should. 1.187 and 1.188 don't. That is the problem. I need someone with both to check it out.
  5. Replies
    6
    Views
    1,760

    Not piercing corectly using DEsigner Basic.

    Using Pro (3.106) I have successfully converted my EZ Box project to have wooden hinges. Joe informed me that they can not upload Pro designed projects (or collections) to the store? So, I decided...
  6. Replies
    3
    Views
    1,366

    But why did it start showing up in my projects...

    But why did it start showing up in my projects that have been in the store for years? Maybe the last item in the change log for 1.186 to 1.187?
  7. Replies
    3
    Views
    1,366

    bit optimization fixed the problem - so in the...

    bit optimization fixed the problem - so in the immoral word of Gilder Radner (SNL many years ago) "never mind"
  8. Replies
    3
    Views
    1,366

    unwanted Floor Feather

    I recently got around to installing 1.187 to replace 1.186. I found that “floor feather” had been added and I can find no way to “un-check it” as is available in 2.xxx and 3.xxx. This causes...
  9. Replies
    4
    Views
    5,912

    Grandkid's thoughts

    A while back, a bunch of our grandkids (older teen to young adult) were gathered in our kitchen. When they left we found this scribbled on a piece of paper. It was done by a grandson who later died...
  10. Replies
    5
    Views
    6,824

    Camper Rolling Wheel Kit

    I am posting this with Joe's permission.
    Clint
  11. Thread: Christmas 2019

    by cestout
    Replies
    4
    Views
    11,853

    Christmas 2019

    Christmas gifts for younger grand and great grand kids. Angels are for two great grand daughters 3 and 3 months, and the triceratopses are for the boys ages 3 to 6(I think). a 3 watt flicker bulb...
  12. Replies
    2
    Views
    1,371

    Red ChristmasTruck revisited

    With Joe's permission, I added rolling wheels to Joe's Truck - and a few other details.
    Clint
  13. Replies
    4
    Views
    14,410

    I checked the screws and retightened with a hand...

    I checked the screws and retightened with a hand driver. Turns freely. Aligned correctly, but each time I reinstall the jig it acts differently - 60 deg past or 160 deg off. Moved from the C...
  14. Replies
    4
    Views
    14,410

    can't calibrate rotaty jig?

    I keep getting range error and mark is about 30 deg off? Haven't done rotary in some time. Had this trouble before and don't remember how I fixed it.
    thanks
    Clint
  15. Thread: STL Files

    by cestout
    Replies
    4
    Views
    15,790

    I have found that some STL files won't load in...

    I have found that some STL files won't load in STL Converter, but if you import them into Blender then export them they work? If you have the Rotary Jig you can import files for that with STL...
  16. Replies
    9
    Views
    2,291

    My opeion - I like Myshop's version but I would...

    My opeion - I like Myshop's version but I would space the letters a little.
    Clint
  17. Thread: lost licenses

    by cestout
    Replies
    6
    Views
    12,770

    What really concerns me is that some of my...

    What really concerns me is that some of my oldest and most used purchased patterns are no longer in the store.
  18. Thread: lost licenses

    by cestout
    Replies
    6
    Views
    12,770

    I plan to call tomorrow.

    I plan to call tomorrow.
  19. Thread: Tree Pattern

    by cestout
    Replies
    12
    Views
    48,562

    Why not export it as an STL file and import that...

    Why not export it as an STL file and import that into Designer?
    Clint
  20. Thread: Fonts Question

    by cestout
    Replies
    5
    Views
    12,080

    I printed out sheets with Ariel font above the...

    I printed out sheets with Ariel font above the symbol font for all the symbol fonts I have. For insistence, C or c will get you a bird on a branch in Kfon .
    Clint
  21. Thread: lost licenses

    by cestout
    Replies
    6
    Views
    12,770

    lost licenses

    Last week my computer upgraded to Windows 10 build 1903. Opened Designer this morning and was not licensed. I updated licenses and got Designer running but all addons are not licensed and a bunch...
  22. Replies
    4
    Views
    14,276

    Thank you all. Oscar, that looks like the...

    Thank you all. Oscar, that looks like the Desert Willow I have in my yard. Racer, that one looks like a weeping willow and might work.
    Clint
  23. Replies
    4
    Views
    14,276

    need a willow tree

    I need a willow tree, preferably wind blown. ptn, stl, obj - anything will do. I can pay for it if required.

    thanks
    Clint
  24. Replies
    2
    Views
    1,189

    Interesting that this is a Commodore power...

    Interesting that this is a Commodore power supply. My first computer was a Commodore 64, then a 128, then an Amiga. A very long time ago.
    Clint
  25. Thread: Return

    by cestout
    Replies
    4
    Views
    12,658

    Don't know why your X gear broke - like Al, I...

    Don't know why your X gear broke - like Al, I have been doing this since 2007. I have two machines, one with 1600 hrs. and the other over 2000 hrs. I have replaced many parts, and like Al I have a...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4