Search:

Type: Posts; User: waynedazey; Keyword(s):

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. You are in Washington?

    You are in Washington?
  2. Moving to Washington from Arkansas but need the...

    Moving to Washington from Arkansas but need the space so not sure how feasible that would be or not at the moment...
  3. Forced to Relocate across Country Selling Carvewright

    :-(:-( Well I am afraid I am moving across country in the next month and need to raise funds for the move :(:(
    I have a Carvewright type B machine for sale: Rubber traction belts upgraded. comes...
  4. Replies
    9
    Views
    1,951

    I have already done the belt upgrade by necessity...

    I have already done the belt upgrade by necessity due to a sandpaper belt roll up. Regarding the Carve Tight I agree the investment from what I have read would be a good one. However, at this time...
  5. Replies
    27
    Views
    4,971

    In hindsite I believe this issue may have been...

    In hindsite I believe this issue may have been caused by a loose bit... not a loose chuck... a loose bit... Heads up people that have this issue in the future...
  6. Replies
    9
    Views
    1,951

    Bit stuck in chuck

    I have a B machine that the carve bit has somehow allowed the set screws on the qc adapter to come loose and become wedged in the QC Chuck... yes you read that right I still have the QC adapter... I...
  7. Replies
    27
    Views
    4,971

    I was able to get it to carve as is by entering...

    I was able to get it to carve as is by entering 15/16... no we shall see how it goes the bit is wedged in there... but I guess I will start a thread to figure that out...
  8. Replies
    27
    Views
    4,971

    actually I dont'think that has anything to do...

    actually I dont'think that has anything to do with it after all... what is the chance since the project was made so many years ago that the firmware could be the issue?
  9. Replies
    27
    Views
    4,971

    figured it out I believe... the set screw on the...

    figured it out I believe... the set screw on the quick change adapter has broken through the quick change chuck and is potruding out by 1/16 from side of quick change chuck....
  10. Replies
    27
    Views
    4,971

    The only place it is saved is on the flash card...

    The only place it is saved is on the flash card anymore... it has been there for 5 years...actually was the project I was working on when my machine had MANY catastrophic failures... And I cn not...
  11. Replies
    27
    Views
    4,971

    Set to Std

    Set to Std
  12. Replies
    27
    Views
    4,971

    81357 I am running a carve I have done years ago...

    81357
    I am running a carve I have done years ago and it has asked me to add the bit and then asked me to enter board thickness
  13. Replies
    27
    Views
    4,971

    Quick question: I am trying to carve a board that...

    Quick question: I am trying to carve a board that is 1 1/32 thick tried entering 1 and 1 1/32 and 1.1 and 33/32... What am I doing wrong?
  14. Thread: US-Arkansas

    by waynedazey
    Replies
    6
    Views
    5,109

    Heber Springs, AR here

    Heber Springs, AR here
  15. Replies
    11
    Views
    2,767

    I had this same issue and after lots of trouble...

    I had this same issue and after lots of trouble shooting all I needed to do was take the back cover off of my Z Motor and clean it out and put it back together to fix.
  16. Replies
    64
    Views
    12,580

    I have to admit the Forum was LOADS of Help Thank...

    I have to admit the Forum was LOADS of Help Thank you. IMPORTANT FYI: ANYTIME YOU DO WHAT I DID ALWAYS REMEMBER ONCE THE ISSUE IS RESOLVED CHECK YOUR HEAD PRESSURE... YOU PROBABLY WILL NEED TO...
  17. Replies
    64
    Views
    12,580

    UPDATE: Because I have grown ever so slightly...

    UPDATE: Because I have grown ever so slightly impatient I put it back together and tested the Z-axis while waiting for a response. It gave me a reading... Time to try this test again it looks...
  18. Replies
    64
    Views
    12,580

    To update I opened the end and it was completely...

    To update I opened the end and it was completely full of saw dust other then cleaning it out and making sure it turns when the z axis move is there anything else I need to look at while in here?
  19. Replies
    64
    Views
    12,580

    Awesome will try that next! At least it is an...

    Awesome will try that next! At least it is an area I have not already looked so if it is there I won't feel like a complete buffoon...
  20. Replies
    64
    Views
    12,580

    what would I need to do to fix that and atleast...

    what would I need to do to fix that and atleast mark it off my list?
  21. Replies
    64
    Views
    12,580

    When I run the Z-Axis Test, I get a little motion...

    When I run the Z-Axis Test, I get a little motion then a fail. a little more motion in different places then others. I really appreciate you folks helping me trouble shoot this issue as you all are....
  22. Replies
    64
    Views
    12,580

    I checked the z gear and all teeth appear fine....

    I checked the z gear and all teeth appear fine. how ever, I believe I am noticing it is more difficult to send it up then to send it down when the machine is off. down goes smooth however up seems to...
  23. Replies
    64
    Views
    12,580

    when power off the z axis seems to move fine, a...

    when power off the z axis seems to move fine, a bit stiff but I may be over thinking that because I have already lubricated and cleaned the four z rail bearings as well as verified they ar turning...
  24. Replies
    64
    Views
    12,580

    I have cleaned the z-rails, idle pulley, and all...

    I have cleaned the z-rails, idle pulley, and all previously mentioned steps.... It is still failing and I am without a clue what is going on now?!? any ideas? I have a Rev B CarveWright with original...
  25. Replies
    64
    Views
    12,580

    With the Z- Axis Motor removed and all tension...

    With the Z- Axis Motor removed and all tension removed from z belt, I am finding the idler pulley to be nearly impossible to move by hand is this normal? If not any ideas how to remedy this?
Results 1 to 25 of 42
Page 1 of 2 1 2