Search:

Type: Posts; User: jakab; Keyword(s):

Page 1 of 4 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    5
    Views
    1,262

    This machine has been sold. Sent from my...

    This machine has been sold.


    Sent from my iPhone using Tapatalk
  2. Replies
    5
    Views
    1,262

    This machine is still up for sale. Anyone in...

    This machine is still up for sale. Anyone in Canada who is interested please let me know. Machine has not been used for a long time, still like new.

    Thanks.

    ...Peter
  3. Replies
    5
    Views
    1,262

    Hi Henry, you almost bought my machine a couple...

    Hi Henry, you almost bought my machine a couple of years ago.

    Same machine, same options. Have used it only once since we last talked, that was a 15 minute carve I believe. So basically no...
  4. Replies
    5
    Views
    1,262

    CarveWright Model C for Sale - Canada SOLD

    JUST REDUCED and added ER11 collets.

    I have the following for sale:


    1) CarveWright Model C, with approximately 39 Power on Hours, 29 Cut Motor Hours. Including memory card and reader, and...
  5. Replies
    267
    Views
    32,566

    I was wondering what is the minimum version of...

    I was wondering what is the minimum version of the CarveWright software required for both making and using the jig.

    Thank you.

    ...Peter
  6. Replies
    26
    Views
    5,009

    I had a table saw accident on Jan 2nd this year....

    I had a table saw accident on Jan 2nd this year. Three finger tips damaged, bones chipped, 7 stitches, just now I'm getting better and can start using my hand again. Feeling on those three fingers is...
  7. Replies
    16
    Views
    2,596

    Thanks for your insight. I'm looking forward to...

    Thanks for your insight. I'm looking forward to using mine when it arrives. Bergerud suggested a few websites to look for bits, so I'll do that and have some on hand for when the ER11 gets here.
    ...
  8. Replies
    16
    Views
    2,596

    Great to know. Mine already shipped, now the wait...

    Great to know. Mine already shipped, now the wait till it gets here :)
  9. Replies
    16
    Views
    2,596

    Thanks for the information DickB. I am sold. I...

    Thanks for the information DickB. I am sold. I remember reading the about the problem with the new LHR 1/8 bits.

    I certainly didn't know about that 2 flute was better than 4 flute and also the...
  10. Replies
    16
    Views
    2,596

    I believe the 6mm adaptor is not included in the...

    I believe the 6mm adaptor is not included in the kit. Will the 1/4 inch adaptor work with 6mm? I see you specifically say ER11M, I take it the M is for metric. is that available separately?

    I get...
  11. Replies
    16
    Views
    2,596

    That certainly makes a lot of sense. I see that...

    That certainly makes a lot of sense. I see that bits don't have to be real expensive and even though they may not last as long they can be replaced more often..

    One question still remains, and I...
  12. Replies
    16
    Views
    2,596

    Thanks for your input. Would you mind sharing the...

    Thanks for your input. Would you mind sharing the URL for the bits? Like you say, there are so many to choose from, I have no idea what to look for, except 1/8 cutting, how about length?

    ...Peter
  13. Replies
    16
    Views
    2,596

    Thanks, that looks like a good alternative. I...

    Thanks, that looks like a good alternative. I take it you use these with a 1/4" collet?
    ...Peter
  14. Replies
    16
    Views
    2,596

    ER11 adaptor. Seeking user experiences

    Much has been said in this Forum about ER11 adaptors. Many seem to have bought them from eBay.

    However, I have not seen many (any) comments from people who have bought them and are using them.
    ...
  15. Replies
    10
    Views
    3,331

    Hi there. Yosemite was released on Thursday 10/16...

    Hi there. Yosemite was released on Thursday 10/16 :)

    Thanks, happy to be up and running again.

    BTW: I had Quartz 2.7.7 installed before, it's used not only by Designer but also some other...
  16. Replies
    10
    Views
    3,331

    OK I figured out a, perhaps temporary, solution....

    OK I figured out a, perhaps temporary, solution. It would seem that the X11 files are now in /opt instead of /usr.

    You can create a symbolic link between the two folders by issuing the following...
  17. Replies
    10
    Views
    3,331

    Hi, I confirm this error with GA Yosemite, same...

    Hi, I confirm this error with GA Yosemite, same error:

    Dyld Error Message:
    Library not loaded: /usr/X11/lib/libGL.1.dylib
    Referenced from:...
  18. Replies
    6
    Views
    1,198

    Thanks Clint, I haven't got around trying it out...

    Thanks Clint, I haven't got around trying it out yet.

    I would love to see some pictures when you do the box.

    ...Peter
  19. Replies
    6
    Views
    1,198

    Thanks Al, I think that lying about the bit size...

    Thanks Al, I think that lying about the bit size is a good tip to get a smoother cut. Also not using a carve region sounds like good advice for reducing carve time.

    Also thank Cestout for your...
  20. Replies
    6
    Views
    1,198

    Another inlay question/challenge

    I was watching this video and I started wondering how could this be done using the CW:

    https://www.youtube.com/watch?feature=player_detailpage&v=oUNMJtBarsY

    It seems so easy on the Shapeoko......
  21. Thread: cutpath problem

    by jakab
    Replies
    29
    Views
    2,453

    And if you carve it again, make sure you spell...

    And if you carve it again, make sure you spell "Reunion" properly :p
  22. Replies
    21
    Views
    3,012

    Very good, thanks Metallus. ...Peter

    Very good, thanks Metallus.

    ...Peter
  23. Replies
    44
    Views
    5,563

    There are lots of PDF to Word converters out...

    There are lots of PDF to Word converters out there. Some even free. See: https://www.pdftoword.com
  24. Replies
    21
    Views
    3,012

    Thanks again DickB, that really clarifies the...

    Thanks again DickB, that really clarifies the issue.

    Now, there is also Jog to Touch, which I understand can be used to measure the board thickness at a predetermined spot on the board, correct?...
  25. Replies
    21
    Views
    3,012

    Thanks DickB, that certainly explains a lot and...

    Thanks DickB, that certainly explains a lot and clarifies many of the grey areas.

    One more question: When you Jog to Position, are you designating the 0,0 position of the design? or just the X...
Results 1 to 25 of 92
Page 1 of 4 1 2 3 4