Search:

Type: Posts; User: Mugsowner; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Thread: -Objects

    by Mugsowner
    Replies
    337
    Views
    99,811

    Sticky: Looks nice Oscar

    Looks nice Oscar
  2. Replies
    8
    Views
    535

    Sent PM to you

    Sent PM to you
  3. Replies
    8
    Views
    535

    Let me check later today after the sun wakes up...

    Let me check later today after the sun wakes up and see what I have. Thinking I should have one somewhere and should be able to come up with the muffler bag as well.
  4. Replies
    4
    Views
    474

    Merry christmas

    Hope everyone is doing well and has a Very Merry Christmas
  5. Replies
    4
    Views
    464

    You would have to get a hold of the designer some...

    You would have to get a hold of the designer some how and ask them if they would be willing to share this info with you.
  6. Looks like the machine is in Mulberry, Florida....

    Looks like the machine is in Mulberry, Florida. This machine was just listed on EBay.
  7. Replies
    3
    Views
    495

    I see all is good now.

    I see all is good now.
  8. Thread: Eagle Scouts

    by Mugsowner
    Replies
    3
    Views
    451

    Not sure if this is what you want,but here it is.

    Not sure if this is what you want,but here it is.
  9. Replies
    3
    Views
    495

    Looks like the copy and paste demons are at work...

    Looks like the copy and paste demons are at work here. The 1/16" carving bit and the 1/8" cutting bit specs seemed to have been copied to the long bits of same size.
  10. The resin area is going to need a very fine paper...

    The resin area is going to need a very fine paper to remove sanding marks. I would think it is a lot like acrylic, which requires very fine paper, to get scratches down to a point where the eye does...
  11. I went to the site and it does seem to be up and...

    I went to the site and it does seem to be up and running. I did not place an order, but was aloud to place items cart.
  12. Replies
    281
    Views
    52,242

    Not having used a UCB, I am guessing here, but I...

    Not having used a UCB, I am guessing here, but I would think you need to enter the project board thickness plus the thickness of the UCB.
  13. Replies
    14
    Views
    2,790

    The new board senors do not have the clear cover...

    The new board senors do not have the clear cover over them any more. I think they proved to be more of an issue than a help.
  14. Thread: Board Sensor

    by Mugsowner
    Replies
    10
    Views
    1,498

    From what I can see the board sensor is not in...

    From what I can see the board sensor is not in stock as it is not listed in the store. When items are not in stock, they do not list them as for sale. Like Lynn stated check your cable connections to...
  15. Replies
    5
    Views
    768

    Great job, it feels awesome to save items from...

    Great job, it feels awesome to save items from the landfill and make them look great again. As far as your issues with the grill, I am thinking wood choice may be the problem. To me it looks like oak...
  16. Thread: Board Sensor

    by Mugsowner
    Replies
    5
    Views
    968

    I have had issues with white items and the board...

    I have had issues with white items and the board sensor. Not sure if it was glare or some other issue. I use masking tape in a T pattern so the tape stays under sensor while it is looking for the...
  17. Replies
    5
    Views
    701

    I have not used jog to corner as of yet, but I do...

    I have not used jog to corner as of yet, but I do use jog to center a lot. Jog to center mode will put the bit in the cenetr of where the machine figured center to be on the Y axis and you are able...
  18. Replies
    253
    Views
    36,649

    As normal, these are great Oscar. I'm sure the...

    As normal, these are great Oscar. I'm sure the ladies will enjoy them for years to come.
  19. Replies
    36
    Views
    5,527

    I have a pvc tube that has a cap glued on one end...

    I have a pvc tube that has a cap glued on one end and another fit loose on the other end. I put the flex shaft in the tube, fill with lube, cap, and let it sit over night. I also have a magnet made...
  20. Replies
    6
    Views
    546

    I would be looking at the brushed due to the rpm...

    I would be looking at the brushed due to the rpm change, that can be a sign of more costly damage happening. After sitting awhile the brushes may be sticking in the holders and not applying the...
  21. Replies
    6
    Views
    807

    sent you a pm

    sent you a pm
  22. Replies
    10
    Views
    1,560

    Oscar you do some great work, however this one...

    Oscar you do some great work, however this one seems to be missing something. The deer looks to be running in air. The sharp edge on the bottom of the mountain does not look natural to me. Not to be...
  23. Thread: Happy 4th

    by Mugsowner
    Replies
    4
    Views
    1,451

    Happy 4th

    Getting ready to head out of town and thought I would take a moment to wish everyone a happy 4th. Keep all your components where they belong, and try not to burn to much down. Enjoy
  24. Thread: Please Help

    by Mugsowner
    Replies
    5
    Views
    784

    Schedule 40 pipe is a standard. Most times you...

    Schedule 40 pipe is a standard. Most times you will see the standard print on the pipe. Thinner pipe will not carry these markings. Schedule 80 is much thicker.
  25. Replies
    121
    Views
    21,474

    Again nice work Oscar

    Again nice work Oscar
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4