Search:

Type: Posts; User: JLT; Keyword(s):

Page 1 of 9 1 2 3 4

Search: Search took 0.00 seconds.

  1. Thread: Wanted to share

    by JLT
    Replies
    10
    Views
    9,961

    Terry, have to echo shortround's observation that...

    Terry, have to echo shortround's observation that the finishing work is very well done! Plus the designs are very pleasing, and recessing the carving within the frame really brings out the body of...
  2. Thread: Custom clock

    by JLT
    Replies
    17
    Views
    5,593

    Dick, nice project as usual! I'm like you too......

    Dick, nice project as usual! I'm like you too... a table saw with a sharp freud blade does a great job jointing a tight glue edge.
  3. Thread: Bathroom Vanity

    by JLT
    Replies
    6
    Views
    2,257

    Thanks for the kind words. Working on a few more...

    Thanks for the kind words. Working on a few more furniture pieces that will make more use of the CW than just carving the feet. Will post those in a few months...
  4. Thread: Bathroom Vanity

    by JLT
    Replies
    6
    Views
    2,257

    Bathroom Vanity

    Been a while since I've posted. I can see that a lot of creatively still flows on this forum!... Had a pair of bathroom vanities bought many moons ago that were made of laminated particle board,...
  5. Replies
    27
    Views
    37,684

    Dick, I have Windows 10 also, along with the...

    Dick,


    I have Windows 10 also, along with the latest Virus and Spyware definitions (version 1.241.72.0) for Windows Defender, and v1.5a doesn't indicate a threat on my workstation. I just now...
  6. Replies
    9
    Views
    1,876

    In another post, I seem to recall it was Dan...

    In another post, I seem to recall it was Dan (bergerud) who had pointed out that you can run back-to-back projects without releasing the board, as long as the project size is the same. Ie, the...
  7. Sharon, the whimsical fish are wonderfully...

    Sharon, the whimsical fish are wonderfully executed! R, Jon
  8. Replies
    33
    Views
    9,955

    Dick, well done! I'm guessing that setting up...

    Dick, well done! I'm guessing that setting up and cutting the compound miters takes longer than the carvings! Looks like a nice tight fit that you must have nibbled your way up to... R, Jon
  9. Replies
    9
    Views
    2,338

    Steve, well done! Nice clean lines, which really...

    Steve, well done! Nice clean lines, which really brings out the emblem! Looks like it's computer ready too! R, Jon
  10. Replies
    8
    Views
    2,627

    Dick, Well done!

    Dick, Well done!
  11. Replies
    14
    Views
    3,713

    Thanks for looking and the compliments. The...

    Thanks for looking and the compliments. The concept isn't original (these types of drawers are sold commercially), although I was never able to find a picture of the slide mechanism, so improvised....
  12. Replies
    14
    Views
    3,713

    Under cabinet knife and spice drawers...

    Built some under the cabinet drawers, mostly using the tablesaw, but the CW came to the rescue to cut the drawer guides, which permit the drawer to slide out horizontally then drop and hold at 45...
  13. Replies
    17
    Views
    4,386

    Mike, simply beautiful carving and finish! -Jon

    Mike, simply beautiful carving and finish! -Jon
  14. Replies
    17
    Views
    3,584

    Dan, how did you arrive at this means of...

    Dan, how did you arrive at this means of calculating the adjustment to the calibration. The manual (Rev 1.54, 01/07/13) states...

    ====================
    To find the magnitude of the change to the...
  15. RocketMan, Am not sure how familiar you are...

    RocketMan,


    Am not sure how familiar you are with my "Radial Vector Program", but it essentially allows one to script the generation of complex line drawings that can be imported into designer. ...
  16. Replies
    18
    Views
    4,155

    Really nice! The gold leaf accents really make...

    Really nice! The gold leaf accents really make the carving pop...
  17. Been dabbling with an advanced version of my...

    Been dabbling with an advanced version of my "Radial Vector Generator", to incorporate height map stroking of vector paths. Still a long ways to go, but as a rough test, hard coded the parameters of...
  18. Replies
    284
    Views
    165,344

    I guess I thought you were looking for a way to...

    I guess I thought you were looking for a way to drop the board just enough to slide it out while the rollers are still on the sled frame. So, if the board is 1/8" proud of the sled frame, then all...
  19. Replies
    284
    Views
    165,344

    After a bit more thought, I'd re-arrange the...

    After a bit more thought, I'd re-arrange the hinges as in the first attachment, and then to tighten, simply twist until the two clamp boards are at 180deg, standing flat on top of each other. The...
  20. Replies
    284
    Views
    165,344

    Haven't studied the design of the carrier sled in...

    Haven't studied the design of the carrier sled in full, but am wondering if a double hinge action clamp might do the trick... (See attached rough sketch.) This would avoid the friction issue. The...
  21. Donnie, Couple of (hopefully helpful)...

    Donnie,

    Couple of (hopefully helpful) observations...


    * Forgive me if you've already worked through this, but it seems like you're going to need at least two sets of rings to make a bowl......
  22. Thread: Darn drones

    by JLT
    Replies
    28
    Views
    30,453

    Nice LG... and a product that can deliver itself!...

    Nice LG... and a product that can deliver itself! ; -) I'm guessing the reference to the vacuum press is to use the CW to make a carbon fiber / resin form, in order to create strong, but light...
  23. Replies
    25
    Views
    5,462

    Dick, Uploaded the next iteration of the...

    Dick,

    Uploaded the next iteration of the Wabble script, including it in a re-upload of the v1.5a zip file at the original post...
  24. Replies
    25
    Views
    5,462

    Yes, makes perfect sense... easy enough to...

    Yes, makes perfect sense... easy enough to incorporate as another parameter, presuming the profile is always an arc, and not a sinusoidal wave... Although off the top of my head, I can think of a...
  25. Replies
    25
    Views
    5,462

    Dick, I've uploaded the latest Radial Vector...

    Dick,

    I've uploaded the latest Radial Vector Generator v1.5a at the original post http://forum.carvewright.com/showthread.php?17794-Make-Gears-with-Radial-Vector-Generator , as I realized that the...
Results 1 to 25 of 224
Page 1 of 9 1 2 3 4