Yes it does have a ground plug. I thought you meant another way of grounding sorry. I do need it where I can disconnect it from the CW. I will only hook it up to the CW when I use it.
Type: Posts; User: Milanth; Keyword(s):
Yes it does have a ground plug. I thought you meant another way of grounding sorry. I do need it where I can disconnect it from the CW. I will only hook it up to the CW when I use it.
I had thought about emailing you. I didn't know if anyone was up on here. I have no ground whatsoever on my dust collector. I have a read a lot about your RingNeck Blues. I wish I had bought it a...
I need to know how to ground my new RingNeck Blues Collector. I just got it today. Now my dust collector is run to a large metal trash can. Then another hose comes out and goes to the machine. How...
Okay after further inspection I have found the problem. It is the wire on the cover that runs under the cover. It is hanging down and stopping the travel. I did not see any more clips for it to fit...
I will check it and be right back.
We replaced the carriage bearings in the Y rail and put it back together. Now when you try to set up the bit the bit won't go all the way to kick the metal panel out for bit setup. Any ideas? I tried...
Thanks I will be ordering them first thing in the morning. I have an order they guy was suppose to pick up this coming Sunday but I will be short 2 plaques. My deadline is before April 8 so I should...
The Z bearings are fine. I fully intend on putting a dc on it now. I have a 4" vacuum system that I use all over my shop. I have it with a large metal trash can at it's side. Most of the debris goes...
My husband said it would be okay on the to 2 bearings but he can't get the seal off the lower 2 without destroying the seal. Okay can you tell me what a DC system is?Is that they dust recovery...
Do you know now much the bearings are?
We have the carriage off the rail now. We figured out if we loosen enough it will come off the rail. My husband removed the seal off the lower bearings. He said he does not think it could be cleaned...
We just figured it out where the seal. We are in the process of trying to remove the seal now and try to clean it. The bottom ones are going to be a different story. We can't even see those. We...
Once again I have answered my own question. We checked the bottom bearings in the same way and both the bottom bearings will barely move. Tomorrow morning I will order all 4 bearings. At that point...
We did loosen the top bearings. One on the right spins freely. We lifted the Z truck slightly and was able to spin the bearing. Now the left bearing is pretty hard to spin. So apparently the right...
After taking everything apart the Z truck moves smoothly across the Y rail. When we took the snap covers off it really looked clean under them. Now if it was the bearings dirty wouldn't it still be...
The screws in the top 2 bearings won't come out so it looks like we will be drilling the screws now. So first thing in the morning I will be ordering new bearings and screws. I guess that answered my...
So I should order new bearings? I know yesterday a guy said just clean the bearings that should and he sent a link. I replaced the Y motor thinking the Y motor was locked up. After replacing the Y...
Do you have to take the Z truck off the Y rail to clean the carriage bearings?? I went to what carvewright link and read how they said to remove the Z truck.
Thanks I will check out the link. It moves up and down fine. It is hard to mover across the Y bar. I just tried to run it and it would not go far enough to kick the plate out to set the bit up to...
Are the carriage bearings on the truck itself? Upper and lower on both side? I had it plugged in backwards. I plugged it in right and tried to carve. It did okay until it came time to load the bit....
I thought my Y motor was bad. I kept getting a error clean Y rail. I had this for 2 days then it locked up and wouldn't move. I finally got it to free up. I carved 2 more plaques. The next day I got...
Okay I will go try it. I did do a search and got some good information. I will let you know if it works.
i took a cuttip and put a little window cleaner on it and cleaned the linse. It worked for 2 carves then it started all over again. Can I loosen the screws to blow it out? That is what I need to...
I keep getting a board sensor error. I did the sensor test and it is only reading at 30 instead of 90. I got a mirror and looked. It looks like there is some dust under the cover. Can I loosen the...
Thanks! I sure thought I had it closed but I guess I didn't! I am sure glad we have the experts like you! :)