Search:

Type: Posts; User: DianMayfield; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    252
    Views
    31,663

    I told it that there was a 1/2 ball nose, and...

    I told it that there was a 1/2 ball nose, and there was a little burn, but light sanding took it out. I use a brass brush on my bits before every use, just to make sure there is no pitch or anything...
  2. Replies
    252
    Views
    31,663

    That's lovely Oscar! I have used a 3/4in core box...

    That's lovely Oscar! I have used a 3/4in core box (?) bit to create a 1/2 circle trough to rest plaques in.
  3. It sounds like the bit plate is not swinging out....

    It sounds like the bit plate is not swinging out. The side away from the keyboard. The bit will bob a down to it two or three times in finding bit. It will repeatedly ask for the bit if it doesn't...
  4. Replies
    11
    Views
    2,445

    It is weird that it deforms the oval! If you give...

    It is weird that it deforms the oval! If you give me the dimensions of your oval, I will create in Corel and cut it there, and post the trimmed piece.
  5. Replies
    11
    Views
    2,445

    Do you have the knife tool? it is on the utility...

    Do you have the knife tool? it is on the utility toolbar. I am not sure which module that comes with. You can cut off the excess part of the oval and delete it.
  6. Replies
    15
    Views
    1,818

    Hi Rick, What is happening when you try to make...

    Hi Rick, What is happening when you try to make the white be the surface? The image is too small to be a clean set of rings, too pixilated. You can design it larger, then resize on the board.

    If...
  7. The 1/16 cutting bit comes with a split collet,...

    The 1/16 cutting bit comes with a split collet, it is not pressed into the standard collet -at least when i purchased them last year.
  8. Replies
    10
    Views
    1,410

    Hi, If you do not have the DXF importer, I can...

    Hi,

    If you do not have the DXF importer, I can save it as a pattern. You just won't be able to tweek it other than size. If you use Corel or other vector programs, the dxf is pretty important to...
  9. Replies
    10
    Views
    1,410

    Hi Pete, I found a file online that had the...

    Hi Pete, I found a file online that had the graphic embedded as a vector drawing. Here is my attempt. It is set to .25 deep, with the distress marks at .05

    PM me and I can send you the MPC or turn...
  10. Replies
    10
    Views
    1,410

    I need to run off to my day job. I am working on...

    I need to run off to my day job. I am working on your graphic. What software version are you using? Do you have the dxf importer? Message me if you would like me to send this to you, put your...
  11. Replies
    3
    Views
    686

    Hi, pics really help solve problems :) To add...

    Hi, pics really help solve problems :)

    To add pics, in the "reply" hit Go Advanced
    Scroll down and Manage Attachments
    At the top right, Add Files, then select and upload.
    They cant be too...
  12. Replies
    1
    Views
    515

    Hi Aaron, Here is a good thread on positioning...

    Hi Aaron,

    Here is a good thread on positioning :)
    https://forum.carvewright.com/showthread.php?30453-Board-Positioning
  13. Replies
    6
    Views
    1,560

    Clint, did you log into your account? It should...

    Clint, did you log into your account? It should show what patterns you have assigned to which machine. I once found that my licenses for some items were still assigned to a really old computer. CW...
  14. Replies
    5
    Views
    890

    His pictures are here: ...

    His pictures are here: https://forum.carvewright.com/showthread.php?30461-Edge-cut-not-square-corners
  15. Replies
    3
    Views
    502

    I would zoom in really close on your design in...

    I would zoom in really close on your design in the software. It looks like it was created that way, and the long sides extend just a hair past the short sides.
  16. Replies
    7
    Views
    875

    Hi Don, I use Jog to Position almost...

    Hi Don,

    I use Jog to Position almost exclusively. I do this to make sure that I control any board imperfections impact on the final design. You can also add projects to a single board with this...
  17. Hi Richard, I am using ver 3.1 When you...

    Hi Richard,

    I am using ver 3.1

    When you open this MPC, do the colors work?
  18. Richard, Read your post again.. sorry! ...

    Richard,

    Read your post again.. sorry!

    Whenever I make a two tone board, I always start with the core thickness. It does't seem to respond predictably if I start with the skin.
  19. Hi Richard, so you don't have the grid to the...

    Hi Richard, so you don't have the grid to the right showing the different color woods that are available normally, you just see the light wood?
  20. Replies
    2
    Views
    1,974

    I have had to click on one of the other icons,...

    I have had to click on one of the other icons, like the circle tool, before hitting the pointer tool to get it to deselect the rotation.
  21. Replies
    6
    Views
    448

    Mugs, I am pretty sure I got the idea from AL,...

    Mugs,

    I am pretty sure I got the idea from AL, who has made most of our mistakes so we don't have to. And is there to help when we do it anyway!
  22. Replies
    6
    Views
    448

    Nathan, Take a 6" piece of packing tape. Stick...

    Nathan,

    Take a 6" piece of packing tape. Stick about 1" of it on one side of the card. Fold it so that about 1" is available to stick on the other side. You now have a 2" tab to pull out the card.
  23. Replies
    8
    Views
    1,145

    Nathan, There is a hole in the threaded rod on...

    Nathan,

    There is a hole in the threaded rod on the right hand side (non-keyboard) near the bottom. You can stick an allen wrench or thick pin in there to turn the rod.
  24. Replies
    1
    Views
    698

    Army Air Assault Wings

    Would anyone have a pattern for Army air assault wings? I bought a file to manipulate, but I suspect that I am stressed out about making the urn and can't concentrate on making it match the style of...
  25. Replies
    3
    Views
    1,177

    I bought my machine 3 months later... wow, where...

    I bought my machine 3 months later... wow, where has the time gone!
    Is this the post?
    https://forum.carvewright.com/showthread.php?22923-Ipad-Tablet-Stand&highlight=IPad
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4