Search:

Type: Posts; User: ekimnamyr; Keyword(s):

Page 1 of 6 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    5
    Views
    4,919

    I have already ran it thru Meshlab.I have done...

    I have already ran it thru Meshlab.I have done quite a bit of that. I have had that error once before I just deleted the file after numerous attempts to figure it out. But now I need to figure it...
  2. Replies
    5
    Views
    4,919

    STL Fail to load

    When loading an stl file I get an Error ststing that(Too much for one table row Unable to fetch results) does anyone have a clue what the problem might be?
  3. Replies
    1
    Views
    3,307

    corrupt file error

    having trouble getting my importer to bring a file in getting corrupt file error , am about 99.9 percent sure the file is ok. I can open it in the 3D viewer and it is there. just cannot bring it in...
  4. Replies
    9
    Views
    2,472

    Yes I understand the issue. This customer has...

    Yes I understand the issue. This customer has over 400.00 in stock now , it would have to be a two sided carve and I have not had a two sided carve that I am Happy with yet.
  5. Replies
    9
    Views
    2,472

    Thanks Berg, Think the process is not worth the...

    Thanks Berg, Think the process is not worth the outcome. Probably better to hand carve the leaf pattern he wants.
  6. Replies
    9
    Views
    2,472

    If you mean a scanner for paper copies. yes.. I...

    If you mean a scanner for paper copies. yes.. I also have the carvewright scanner for copying patterns. yes i can do that also.
  7. Replies
    9
    Views
    2,472

    Thanks Oscar. did not think it was going to be...

    Thanks Oscar. did not think it was going to be simple..
  8. Replies
    9
    Views
    2,472

    gunstock carving

    Does any one have a suggestion on how to setup and carve a pattern on a gunstock in the general area circled?
  9. Replies
    2
    Views
    967

    Thanks Floyd, Will give it a try

    Thanks Floyd, Will give it a try
  10. Replies
    2
    Views
    967

    favorites folders

    How many Favorites folders do we need in our library? I know that there have been other posts about this. I have two main folders that have diferent patterns in them, I by mistake clicked on one in...
  11. Replies
    11
    Views
    8,314

    The response to my issue was great!!! of all the...

    The response to my issue was great!!! of all the paths I have been given I am sure that I will get my project completed..
    Thanks to all involved really appreciate it.
    Mike
  12. Replies
    11
    Views
    8,314

    Centerline would be better

    Centerline would be better
  13. Replies
    11
    Views
    8,314

    Thanks to all that had input, That is all that...

    Thanks to all that had input, That is all that there is for an image, I tried to make a pattern as was suggested couple of times, could not get a smooth clean pattern to carve. Need more practice I...
  14. Replies
    11
    Views
    8,314

    technique picture to pattern

    Could someone give a hand in cleaning up this picture? Would like the web address taken out & ph number as well.
    Any help would be appreciated.
    thanks.
  15. Replies
    2
    Views
    1,707

    Thanks Oscar, will give it a try. Do have a...

    Thanks Oscar, will give it a try. Do have a router Thanks!
  16. Replies
    2
    Views
    1,707

    deer skull mount

    Does any one know where I can get a pattern for deer skull mount board? Have seen them in catalogs but want to personalize it. looking for one that has the edge with sculpting on it that looks like a...
  17. Replies
    15
    Views
    7,649

    Welcome back Bruce,,, missed your comments and...

    Welcome back Bruce,,, missed your comments and input here on the forum, glad you are back!!!!!!!
  18. Replies
    3
    Views
    1,205

    thanks will check that out tomorrow.

    thanks will check that out tomorrow.
  19. Replies
    3
    Views
    1,205

    traction belts

    Ok finally broke down and put rubber traction belts on. Everything went smooth, machine operates as it should, Only problem is when belts run in direction of right when standing at keyboard side...
  20. Thread: Forum page

    by ekimnamyr
    Replies
    4
    Views
    12,147

    upper right hand corner of page, type in...

    upper right hand corner of page, type in helicopter, in search box
  21. Replies
    1
    Views
    12,109

    found the answer. 1.00 is max depth for 1/8 cut...

    found the answer. 1.00 is max depth for 1/8 cut bit
  22. Replies
    1
    Views
    12,109

    board thickness

    how thick of a board can I cut thru with an 1/8 cutting bit. Want to cut .900. can it be done?
  23. Thread: cutouts

    by ekimnamyr
    Replies
    1
    Views
    941

    cutouts

    making a pattern 1.5 wide 14.0 long with an S curve in it. Want to make several of these cut outs, some now some later. Want to cut these out with a .125 cut bit. after I save the pattern and bring...
  24. Thread: technique

    by ekimnamyr
    Replies
    5
    Views
    1,422

    It is a picture I took and imported , I placed it...

    It is a picture I took and imported , I placed it on bumps and the picture had the bumps on it.
  25. Thread: technique

    by ekimnamyr
    Replies
    5
    Views
    1,422

    technique

    I have a carve region that has a surface applied to it, Lets say bumps. is there a way to put a picture on top of that surface and not have the bump surface show on it, The picture?
Results 1 to 25 of 134
Page 1 of 6 1 2 3 4