Search:

Type: Posts; User: joepei; Keyword(s):

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Replies
    12
    Views
    1,367

    Thanks will do!

    Thanks will do!
  2. Replies
    12
    Views
    1,367

    5th Time must be the charm! I assembled and...

    5th Time must be the charm! I assembled and really gave it a hard crank and the clutch popped and started moving. Thought i was going to break something. Anyway the click is 5 times stiffer than the...
  3. Replies
    12
    Views
    1,367

    Any way to test the clutch without assembling the...

    Any way to test the clutch without assembling the side panel back on the machine? The shop is 72 degrees always so the temp is not a problem.
  4. Replies
    12
    Views
    1,367

    Yes, use the grease to hold the clutch in place...

    Yes, use the grease to hold the clutch in place as per video. I tried more spacers on the spring but no difference.
  5. Replies
    12
    Views
    1,367

    Spring is against the clutch plate.

    Spring is against the clutch plate.
  6. Replies
    12
    Views
    1,367

    Took apart the assembly and reassembled twice....

    Took apart the assembly and reassembled twice. Gear and handle spinng freely before putting back on the machine. Assembled back on the machine. When i lower the head the clutch is still not clicking....
  7. Replies
    12
    Views
    1,367

    Clutch torque plate

    Hi All,
    I just installed a new clutch torque plate. Followed the video instructions. After i had it assembled the clutch is not slipping when I lower the head to the board. any ideas before I take...
  8. Replies
    11
    Views
    3,753

    I will do another scan. When i lay the carved...

    I will do another scan. When i lay the carved vent over the plastic one and center the vents the carved one is smaller on all sides. This is the first time i have had this problem on a scan, but this...
  9. Replies
    11
    Views
    3,753

    vent scan size

    I enlarged the board size. If you open the mpc in the software and click on the vent the box that gives the size comes up. That box is not matching up with the carving edges on the right and bottom...
  10. Replies
    11
    Views
    3,753

    ford vent

    Yes i am. So I deleted the back side and adjusted the size. When i highlight the image the size square still lines up on the left and top facing, but is off the carve on the bottom and right side.
  11. Replies
    11
    Views
    3,753

    carve scan coming out small

    I am just getting back to this vent. I tried adjusting the size in designer, but when i try to save it, the program changes the size to a larger one again. I have attached a picture of the MPC. If...
  12. Replies
    11
    Views
    3,753

    No but i did save it directly from scan into the...

    No but i did save it directly from scan into the carve pattern tool list, so no cut path option was involved that i saw.
  13. Replies
    11
    Views
    3,753

    carved scan coming out small

    i have scanned a dash vent from a 31 ford. The scan came out well and the carving looks good. The problem is the carving is coming out 1/8" smaller then the original. It looks like the carving bit is...
  14. joepei

    Thanks guys. .01 is better than .59 deep. i have converted other STL's before and was able to get rid of the border when importing it with the raise lower, but not this time.
    Thanks
  15. waterfall pattern

    I cant seem to get rid of the background cut line. Can anybody help?
  16. how to get rid of a cut line from stl conversion

    Hi All. I just installed and downloaded an STL file to the patterns. I am getting a deep square cut around the pattern which seems to be the outside of the uploaded STL. Any idea how to get rid of...
  17. Thread: loons on lake

    by joepei
    Replies
    4
    Views
    940

    Thanks I found another one.

    Thanks I found another one.
  18. Thread: loons on lake

    by joepei
    Replies
    4
    Views
    940

    loons on lake

    Does anyone know the name of the "loons on lake pattern" in the Pattern Store. I found it, tried it and did not write the exact name down. after a lot of time wasted still have not come across it.
  19. Replies
    4
    Views
    845

    picking carving problem

    When i go to the carving choice and select one, my pointer comes up in rotate mode so i can't pick and place the carving. Any ideas?
    joe
  20. Replies
    2
    Views
    504

    softtware question

    I am carving a crib board. It is primarily centerline text and lines with 1/8 holes drilled. Finished all the centerline and line cuts, machine was ready for the bit change to 1/8 to drill holes and...
  21. Replies
    14
    Views
    1,019

    It worked great, i will post a pic when the table...

    It worked great, i will post a pic when the table is done. Thanks!
  22. Replies
    14
    Views
    1,019

    Thanks! looks perfect. I will give it a try. Joe

    Thanks! looks perfect. I will give it a try.
    Joe
  23. Replies
    14
    Views
    1,019

    That would be great, i do not have 3D yet. The...

    That would be great, i do not have 3D yet. The poker chips come in 39 and 40mm. I am going to make for the 40mm so i am covered for both. The trough would have to be 4"L x 1 11/16"W x 3/4"D.
    Thanks...
  24. Replies
    14
    Views
    1,019

    next question, is there any way to adjust the...

    next question, is there any way to adjust the curve to be round. it now has more of a tapered side than fully round.
  25. Replies
    14
    Views
    1,019

    Thanks! I really have to find more time to spend...

    Thanks! I really have to find more time to spend with this machine!!
Results 1 to 25 of 51
Page 1 of 3 1 2 3