Search:

Type: Posts; User: fwharris; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    6
    Views
    116

    Call CarveWright

    Call CarveWright
  2. Replies
    28
    Views
    2,968

    The vendor, Vectorart3D, was/is a vendor in the...

    The vendor, Vectorart3D, was/is a vendor in the pattern depot store but some of their patterns are no longer for sale there.. But you can find it on there web site store...
  3. For accurate 2 sided carves you need to make sure...

    For accurate 2 sided carves you need to make sure your machine does not have any Y offsets. Look up the calibrate Y offset procedure to determine if you need to do the re calibration.

    There is...
  4. Are these patterns that you have purchased before?

    Are these patterns that you have purchased before?
  5. Get/download any patterns that were purchased...

    Get/download any patterns that were purchased from CarveWright to to your owners/registration account and you can download them from there. You can access it from the help tap in designer or from...
  6. Replies
    1
    Views
    161

    I doubt that they will work.

    I doubt that they will work.
  7. Replies
    4
    Views
    318

    You can adjust just the scoop part by drawing an...

    You can adjust just the scoop part by drawing an oval over it and apply a carve region to over ride the scoop but that might leave a ridge in the scoop. Not the best method. I was talking about...
  8. Replies
    4
    Views
    318

    To change the path area around the spoon you can...

    To change the path area around the spoon you can drag in the path line, click and hold the yellow dots. Or do a new path offset that is smaller than the original offset.

    To change the depth of...
  9. You are doing double posts on the same subject....

    You are doing double posts on the same subject. Please try to keep just one post going.

    Reformat the card.
  10. Belt tension, dirty Y rails and bearings,...

    Belt tension, dirty Y rails and bearings, something in the way of the Y truck and stopping it from traveling, flex shaft touching/rubbing on the top cover. Who does it move with the power off, does...
  11. Replies
    4
    Views
    218

    Glad that did it. Make sure you check the head...

    Glad that did it. Make sure you check the head pressure each day that you use the machine.
  12. Replies
    4
    Views
    218

    You might need to add a thin washer (clutch...

    You might need to add a thin washer (clutch spacer washer) to the shaft of the crank handle. https://store.carvewright.com/product.php?productid=16321&cat=255&page=1

    If you have an older machine...
  13. Thread: wooden spoon

    by fwharris
    Replies
    2
    Views
    201

    There are several spoon pattern and projects...

    There are several spoon pattern and projects posted here. Take a look in the pattern sharing section. Search is your friend, just put your search "topic" in quote marks.
  14. Replies
    26
    Views
    6,646

    See my reply on your original question on this......

    See my reply on your original question on this... https://forum.carvewright.com/showthread.php?30711-Rotary-lamp-settings&p=274656#post274656
  15. Replies
    11
    Views
    474

    Blue tape will not work, it is to dark and will...

    Blue tape will not work, it is to dark and will look like there is no board to the machine. You probably got a "scale project to board" error message as the machine saw your board smaller (width or...
  16. Replies
    5
    Views
    195

    Dale, That is good to know about Sculptor. Do...

    Dale,
    That is good to know about Sculptor. Do as Connie said for getting it to open in PE. You can not change a mpc back to a pattern. The mpc is the board that has the pattern on it. If you want...
  17. Replies
    5
    Views
    195

    Without seeing the full image I would say either...

    Without seeing the full image I would say either would/should work. I have both but use PE much more than I do Sculptor. That is probably do to I started out with PE and have learned the tools and...
  18. Replies
    11
    Views
    474

    Could it be faulting out because of the white...

    Could it be faulting out because of the white color of the pipe? Do a board sensor check to see what the readings are when over the pipe.
  19. Replies
    3
    Views
    136

    No not necessarily. Any area between the side...

    No not necessarily. Any area between the side rails / end blocks and the slab can be covered with masking tape or white paper to fool the board sensor during the board measurement steps.
  20. Replies
    3
    Views
    136

    Yes you will need to set up a sled so that you...

    Yes you will need to set up a sled so that you can carve on the slab. A flat base with side rails the same thickness as the slab. If the ends are straight/square you probably will not need end...
  21. Replies
    2
    Views
    256

    Just type in the angle that you want it to be set...

    Just type in the angle that you want it to be set at.
  22. Replies
    7
    Views
    448

    Yes, not all are created the same! Some people...

    Yes, not all are created the same! Some people get a little irritated at Designer for not importing an STL when in fact it is a STL issue. I still wonder about some of those STL files that seem to be...
  23. Replies
    7
    Views
    448

    What is the issue with 2.xx? Do you have 3.xx to...

    What is the issue with 2.xx? Do you have 3.xx to see if they work with that version and how about Basic?
  24. Replies
    11
    Views
    474

    I would verify the thickness of the pipe, it is...

    I would verify the thickness of the pipe, it is thinner than regular litho material. According to the instructions the pattern depth should be Set the depth to .170 and height to 999 and set Bit...
  25. Replies
    3
    Views
    274

    I would check the head pressure.

    I would check the head pressure.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4