Search:

Type: Posts; User: joepei; Keyword(s):

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Replies
    3
    Views
    730

    Thanks, yes it was firmly pushed in with the...

    Thanks, yes it was firmly pushed in with the plastic pulled back. I will put a small dap of caulking on the connect.
    Thanks
  2. Replies
    3
    Views
    730

    z qaxis stall question

    just put a new z motor in. Did 6 crib boards without a problem, on the 7th, I got a z axis stall after 90 percent of the holes were drilled. I went through the Carvewright trouble shooting checklist...
  3. Replies
    2
    Views
    682

    lines in carving

    I am having a strange problem in my carve. I have done 5 of these with perfect results. On the 6th carve the machine cut deeper lines across the carving in the middle of the carve but not at the...
  4. Thread: tracking issue

    by joepei
    Replies
    5
    Views
    1,053

    I do have tape on the bottom of the sled. I will...

    I do have tape on the bottom of the sled. I will try cleaning the tracking wheel. Looking at the failed attempt there is a small glitch on the start end of all the boards and a bad alignment at the...
  5. Thread: tracking issue

    by joepei
    Replies
    5
    Views
    1,053

    tracking issue

    I am having trouble with the machine going off track when carving.
    I attached two pictures to illustrate. The first one shows the lines and holes not aligning. I had three carves similar to this. At...
  6. Replies
    0
    Views
    955

    x drive gear replace

    I just got in the new replacement X Drive gear. I installed the gear, but when i put the screw in that goes through the hole in the large gear and tighten it it jams the gears. If i take that screw...
  7. Replies
    3
    Views
    5,186

    Help with pattern

    Hi I have been asked by a local non profit to make this labyrinth. It is based on overlapping hearts. Any ideas on how to trace the outline and then use a 1/2" ballpoint bit to route? The sample one...
  8. Replies
    12
    Views
    3,384

    Thanks will do!

    Thanks will do!
  9. Replies
    12
    Views
    3,384

    5th Time must be the charm! I assembled and...

    5th Time must be the charm! I assembled and really gave it a hard crank and the clutch popped and started moving. Thought i was going to break something. Anyway the click is 5 times stiffer than the...
  10. Replies
    12
    Views
    3,384

    Any way to test the clutch without assembling the...

    Any way to test the clutch without assembling the side panel back on the machine? The shop is 72 degrees always so the temp is not a problem.
  11. Replies
    12
    Views
    3,384

    Yes, use the grease to hold the clutch in place...

    Yes, use the grease to hold the clutch in place as per video. I tried more spacers on the spring but no difference.
  12. Replies
    12
    Views
    3,384

    Spring is against the clutch plate.

    Spring is against the clutch plate.
  13. Replies
    12
    Views
    3,384

    Took apart the assembly and reassembled twice....

    Took apart the assembly and reassembled twice. Gear and handle spinng freely before putting back on the machine. Assembled back on the machine. When i lower the head the clutch is still not clicking....
  14. Replies
    12
    Views
    3,384

    Clutch torque plate

    Hi All,
    I just installed a new clutch torque plate. Followed the video instructions. After i had it assembled the clutch is not slipping when I lower the head to the board. any ideas before I take...
  15. Replies
    11
    Views
    20,994

    I will do another scan. When i lay the carved...

    I will do another scan. When i lay the carved vent over the plastic one and center the vents the carved one is smaller on all sides. This is the first time i have had this problem on a scan, but this...
  16. Replies
    11
    Views
    20,994

    vent scan size

    I enlarged the board size. If you open the mpc in the software and click on the vent the box that gives the size comes up. That box is not matching up with the carving edges on the right and bottom...
  17. Replies
    11
    Views
    20,994

    ford vent

    Yes i am. So I deleted the back side and adjusted the size. When i highlight the image the size square still lines up on the left and top facing, but is off the carve on the bottom and right side.
  18. Replies
    11
    Views
    20,994

    carve scan coming out small

    I am just getting back to this vent. I tried adjusting the size in designer, but when i try to save it, the program changes the size to a larger one again. I have attached a picture of the MPC. If...
  19. Replies
    11
    Views
    20,994

    No but i did save it directly from scan into the...

    No but i did save it directly from scan into the carve pattern tool list, so no cut path option was involved that i saw.
  20. Replies
    11
    Views
    20,994

    carved scan coming out small

    i have scanned a dash vent from a 31 ford. The scan came out well and the carving looks good. The problem is the carving is coming out 1/8" smaller then the original. It looks like the carving bit is...
  21. Replies
    10
    Views
    18,527

    joepei

    Thanks guys. .01 is better than .59 deep. i have converted other STL's before and was able to get rid of the border when importing it with the raise lower, but not this time.
    Thanks
  22. Replies
    10
    Views
    18,527

    waterfall pattern

    I cant seem to get rid of the background cut line. Can anybody help?
  23. Replies
    10
    Views
    18,527

    how to get rid of a cut line from stl conversion

    Hi All. I just installed and downloaded an STL file to the patterns. I am getting a deep square cut around the pattern which seems to be the outside of the uploaded STL. Any idea how to get rid of...
  24. Thread: loons on lake

    by joepei
    Replies
    4
    Views
    4,804

    Thanks I found another one.

    Thanks I found another one.
  25. Thread: loons on lake

    by joepei
    Replies
    4
    Views
    4,804

    loons on lake

    Does anyone know the name of the "loons on lake pattern" in the Pattern Store. I found it, tried it and did not write the exact name down. after a lot of time wasted still have not come across it.
Results 1 to 25 of 58
Page 1 of 3 1 2 3