Search:

Type: Posts; User: fwharris; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.04 seconds; generated 53 minute(s) ago.

  1. Thread: Err-e03-0400

    by fwharris
    Replies
    2
    Views
    134

    http://support.carvewright.com/edge-detection-fail...

    http://support.carvewright.com/edge-detection-failure-message/
  2. Thread: Err-e03-0400

    by fwharris
    Replies
    2
    Views
    134

    The board sensor is faulting out when trying to...

    The board sensor is faulting out when trying to find the end or edges of the board.
  3. Replies
    2
    Views
    166

    Lori, The default bit for pattern type...

    Lori,

    The default bit for pattern type carvings like you have set up is always the 1/16" tapered ball nose carving bit. It can be seen in the "board settings"/"Pattern bit" settings. If a new...
  4. Replies
    12
    Views
    298

    When you do a "center both" it will put...

    When you do a "center both" it will put everything selected to the center of the board vertically and horizontally. Do one at a time and only center of the horizontal. Them position as needed.
  5. Replies
    12
    Views
    298

    Do a board measure on that last board. I bet the...

    Do a board measure on that last board. I bet the machine is seeing it just a little under your design size and that is why you are getting the scale message.

    I always design for my finished board...
  6. Replies
    12
    Views
    298

    Just do a board measurement without loading the...

    Just do a board measurement without loading the project.

    Are you saying YES to under the rollers or NO? it does make a difference.. see my comments from earlier...
  7. Replies
    12
    Views
    298

    It looks like you said YES to staying under the...

    It looks like you said YES to staying under the rollers. When you do that the machine will add 7" to your design board size. What was your design size? If it was 19" and you used a 26" board to...
  8. I run both versions on my lap top and no issues....

    I run both versions on my lap top and no issues. I did find out that the last version installed is the default version when you try to open an existing project file.

    I do not recall if this has...
  9. Yes you can delete and reinstall without loosing...

    Yes you can delete and reinstall without loosing your settings.

    You mentioned earlier about finding some bent pins, could that still be your issue?

    You can recover a stopped carving by...
  10. Thread: Gun Rack help

    by fwharris
    Replies
    4
    Views
    143

    You should be able to make one off of that...

    You should be able to make one off of that drawing or find one to purchase.
  11. Sounds like success is happening! An extra card...

    Sounds like success is happening! An extra card is handy. You can be designing and up loading while the machine is carving away.
  12. Thread: Gun Rack help

    by fwharris
    Replies
    4
    Views
    143

    Got to a gun store and look at and measure one.

    Got to a gun store and look at and measure one.
  13. That sounds like some progress was made. Lets...

    That sounds like some progress was made. Lets hope the updated firmware was your issue. To prevent damaging the card when you are taking the card out of the machine use some duct tape to make a pull...
  14. reformat the card and reflash the firmware. do...

    reformat the card and reflash the firmware. do the through the flash manager
  15. Replies
    17
    Views
    278

    Great job!

    Great job!
  16. Replies
    17
    Views
    278

    Yes the bathroom scale is probably the less used...

    Yes the bathroom scale is probably the less used tool for the machine and should be used each day/time when you are starting up a new session of carves.

    To increase the head pressure you can add...
  17. Thread: lost patterns

    by fwharris
    Replies
    2
    Views
    80

    Mitch, If you think you still have the...

    Mitch,

    If you think you still have the patterns on your computer try doing a search for them. If using windows use the search window that is usually at the bottom left corner of the screen.
    ...
  18. Replies
    17
    Views
    278

    When I said "designs" I was talking about the...

    When I said "designs" I was talking about the project you are making and the design elements you are placing on the board. All patterns and carve region areas including raster text style you can set...
  19. Replies
    17
    Views
    278

    What quality setting are you using when uploading...

    What quality setting are you using when uploading the project to the card? Are you setting the bit optimization to best on your designs? The best and optimal settings on upload will give you the best...
  20. Replies
    17
    Views
    278

    It does carve very well but as stated it is very...

    It does carve very well but as stated it is very dusty and good dust collection is a must.
  21. Replies
    10
    Views
    277

    Thanks for the feedback. Since they are all the...

    Thanks for the feedback. Since they are all the pressed on adapters just make sure you are setting the bit all of the way into the chuck so that the collar is against the chuck.

    Yes, the 1/8"...
  22. Replies
    10
    Views
    277

    Yes it is okay to post pictures and a lot of...

    Yes it is okay to post pictures and a lot of times they really help with narrowing down the issue. Glad to hear you were able to finish the project. On your error message, if you select #2 carry on...
  23. Replies
    10
    Views
    277

    Were you getting the "please load bit" message...

    Were you getting the "please load bit" message each time? If so the bit plate was not being pushed out far enough for the bit to come down and touch down 2 times to measure it.

    This is a link to...
  24. Replies
    6
    Views
    264

    The cut motor switch is not the same as the cover...

    The cut motor switch is not the same as the cover open switch. It is on the opposite end of the cover.
    ...
  25. Replies
    6
    Views
    264

    It is probably not the controller. I would look...

    It is probably not the controller. I would look at the cover switch (bit plate end of the cover), the wire connection at the motor, the X termination board on the bottom of the machine right side for...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4