Search:

Type: Posts; User: chkorte; Keyword(s):

Page 1 of 12 1 2 3 4

Search: Search took 0.01 seconds.

  1. Thread: Board sensor

    by chkorte
    Replies
    1
    Views
    484

    Board sensor

    Board sensor
    I have recently had a problem with the board sensor on one of my Carvewright machines. It went from measuring the boards most of the time and occasionally giving me a board sensor error...
  2. Replies
    5
    Views
    625

    Thanks forthe info, that probably explains why I...

    Thanks forthe info, that probably explains why I was having so much trouble getting theprogram to save.
  3. Replies
    5
    Views
    625

    Thank you for your reply. Everything that you...

    Thank you for your reply. Everything that you said I should try I had already done and it did no good. I tried saving it in different folders and under a different file and it did no good. I do...
  4. Replies
    5
    Views
    625

    trouble saving pattern

    Greetings everyone, first I have to say that I have not been posting for long time basically because my MS has progressed to the point that I am unable to use my Carvewright machine without...
  5. Replies
    6
    Views
    815

    Thank you that took care of my problem. Now I can...

    Thank you that took care of my problem. Now I can open up all of my patterns. Thank you very much.
  6. I think theproblem I’m having is because of the...

    I think theproblem I’m having is because of the version of designer that I reinstalled.There are only two versions of designer available to reinstall, basic and pro.Now I reinstalled designer basic...
  7. Replies
    6
    Views
    815

    I have thisproblem when I had my windows 10...

    I have thisproblem when I had my windows 10 update. I reinstalled designer and it broughtback my carvewright program, but after I had reinstalled designer not all of myfiles or patterns would open....
  8. Greetings everyone and Merry Christmas - Can You Help

    Greetings everyone and Merry Christmas. I have been a member of the carvewright forum for several years and until the last year or so a regular participant and contributor on the forum but my MS has...
  9. Replies
    12
    Views
    1,233

    I don't know what happen. When I have time I'll...

    I don't know what happen. When I have time I'll try and jet you know. Thanks for the info.
  10. Replies
    10
    Views
    953

    I did this one a while back

    I did this one a while back
  11. Replies
    12
    Views
    1,233

    I was getting ready to try cutting my pattern...

    I was getting ready to try cutting my pattern again. I was planning to put small pieces of wood, one on the bar by the brass roller and one on the sliding bar to try to fool the machine when I got an...
  12. Replies
    12
    Views
    1,233

    Yes and Yes

    Yes and Yes
  13. Replies
    12
    Views
    1,233

    Sorry for taking so long to reply but I’ve been...

    Sorry for taking so long to reply but I’ve been busy with family stuff.
    The board is 1.625” thick. The bit does not touch by the brass roller. The chuck can’t get past the board, same situation with...
  14. Replies
    12
    Views
    1,233

    The only thing it asks me is "RETRY" or "ABORT"

    The only thing it asks me is "RETRY" or "ABORT"
  15. Replies
    12
    Views
    1,233

    Bit won’t touch sliding bar

    BIT WON’T TOUCH SLIDING BAR
    I have tried several times to cut the attached pattern with no success. I even tried cutting top and back as separate patterns with the same results. Each time the...
  16. Replies
    10
    Views
    817

    Last night I shut everything down and now this...

    Last night I shut everything down and now this morning when I start everything up again I go to “Flash Manager” and the ”BAD” is gone and I am able to re-install the firmware. Go Figure!
  17. Replies
    10
    Views
    817

    Firmware won't re-flash. "BAD" still there.

    Firmware won't re-flash. "BAD" still there.
  18. Replies
    10
    Views
    817

    It didn't ask me to do anything.

    It didn't ask me to do anything.
  19. Replies
    10
    Views
    817

    Problem with memory card

    I am having a problem with my memory cards. Today I went to upload a new project onto a card. I put a card in the card reader and plugged it in the usb port. Then I clicked on “File” and “Flash...
  20. Thread: Harp

    by chkorte
    Replies
    11
    Views
    1,229

    I only have the one picture for now. I used a...

    I only have the one picture for now. I used a digital tuner to tune so it sounds pretty much like the ones you were listening to.
  21. Thread: Harp

    by chkorte
    Replies
    11
    Views
    1,229

    Harp

    I finally finished a project I started about a year ago. Most of that year was spent on refining the pattern on the computer while working around other commitments. Also I tend to work a little slow....
  22. I bought a new allen screw for my RC at Ace...

    I bought a new allen screw for my RC at Ace Hardware.
  23. Replies
    27
    Views
    8,358

    Will these work?

    Will these work?
  24. Replies
    6
    Views
    1,571

    I needed to replace the allen head screw in my RC...

    I needed to replace the allen head screw in my RC after about 5 years. I found one at Ace Hardware. I use an allen head screw driver bit glued into a socket on the end of a 15” extension with a ¼”...
  25. Replies
    11
    Views
    1,637

    I haven’t finished it yet but this is what I’m...

    I haven’t finished it yet but this is what I’m doing with my Winchester model 94 Golden Spike Commemorative.
Results 1 to 25 of 288
Page 1 of 12 1 2 3 4