I would be interested in the controller if you part it out, or I would be willing to buy the whole machine at a reasonable price. Please reply if interested to (cyrilk@kristacomputers.com).
Type: Posts; User: caklmk; Keyword(s):
I would be interested in the controller if you part it out, or I would be willing to buy the whole machine at a reasonable price. Please reply if interested to (cyrilk@kristacomputers.com).
I am looking for a controller
If you have your old board sensor, take a box cutter knife and carefully remove the side. You can then blow it out and it will work fine without the side cover. I've been carving for two or more...
I need a controller, a y axis motor, and a z axis motor. I am also needing a full set of y and z axis bearings; however, I think I want new bearings. You may wonder why I need so many parts. While...
For some time my machine places the carvings on my board 1/4" off center. The Carvewright techs tell me to recalibrate my offsets which does nothing to correct the problem as the boards are measured...
On one of my cribbage board carvings I noticed that the outer edges of a region were perfectly rounded from the surface of the carving down to the floor of the region. I really like the appearance...
I find that if I make them with sports logos it doesn't matter if customers haven't even heard of cribbage as the cribbage holes are a nice decoration around your favorite sports team logo. I put a...
I agree that the sliding cover works very well. My only reason for using the key locker was time. It requires about 30 minuets of carving time or about the same as your method. I make 2 to 3...
Since a started making cribbage boards with my machine I always wondered why nobody had come up with a solution in which cribbage pegs could be stored in the board. I did come up with a simple...
Thanks Al, When you asked if the 3rd bit was shorter, which it is, I knew what was wrong. I replaced the bearings in the z truck and it moved up and down like a dream until I hooked up the belt and...
I am getting this error more and more often, but not always. It usually happens on the second bit change on a three bit carve. I can select re-find which always returns the same message. When I...
I use split set collars to maintain the bit depth insertion into the collet. I got them from McMaster Carr supply in Chicago.
After 575 hours of carving I was having low board sensor readings and had to resort to masking tape etc. until it got so bad I couldn't carve anymore. I replaces the sensor and went from a 152...
Thanks for the help. There was a problem in my library files which I caused and I had to have tech support help me correct it. It does work just fine as you instructed.
Thanks
Hi, I'm confused as usual. When I highlight a pattern and extract it I am asked for a category. If I type in an existing one where I would like it to appear it refuses as the category already...
I am from Chippewa Falls, WI and am a packer fan. I am not what one would call a die hard fan, but like professional football in general. I'm not very proud of them right now,but I am sure they...
Thanks so much. I'm embarrased. I think what happened was when I first put the G on a blank board it defaulted to .25 depth. When I then changed it to 0.00 it was hidden which makes sense. I...
Thanks for the help. I do have a closed path and am able to carve a region. I want to bring the G to the surface of the board. Am attaching the MPC file. Thanks65986
I recently needed the G used in the Packer logo. That font is not available due to copy wright infringement. Anyway, I created one with various arcs and lines which looks just fine. When I use it...
This is purely for your information as my problem has been resolved. Within 2 days of getting my machine and after only a few carves my flex cable was getting uncomfortably hot to the touch. I...
To add fonts you open settings and then open the control panel.
There is a font folder there which you open. Then open the font and drag it into the font folder and windows will register it and it...
I had no problem finding the liquid wrench chain lube with moly at the local Blaine Farm and Fleet Store. It may be possible to purchase it on line.
Thanks everyone for the help. I did actually find them. I was just frustrated when I didn't know where they were going and there wasn't anything the software documentation to explain it.
Thanks...
I am trying to extract a pattern from a current project and add it to my library. When I highlight the pattern and click on Extract Pattern from the tools it opens a box and asks for a category. ...
I have had my machine for 3 weeks and already have almost 200 hours on it. I only used the cut pattern 1 time. I have a table saw and a good cut off saw which does a much better job and saves a lot...