Search:

Type: Posts; User: bergerud; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.04 seconds.

  1. The 1/64th was because each face edge was also...

    The 1/64th was because each face edge was also being cut down 1/64th as the sphere was being carved. The cube was getting smaller as the procedure progressed.
  2. What you want to do is actually very difficult as...

    What you want to do is actually very difficult as it requires accuracy which is not easy to get from the machine. Repeatability for all six sides, in my opinion, can only be done if you make a jig...
  3. Replies
    2
    Views
    175

    It is just a different wood texture. Under view -...

    It is just a different wood texture. Under view - texture - lithopane
  4. Replies
    7
    Views
    531

    You could also just take a picture. Best to be as...

    You could also just take a picture. Best to be as far away as possible and zoom in. Put the object on a white background. Raise or lower to remove the background when importing into Designer.
  5. In fact, the brass roller encoder is the same as...

    In fact, the brass roller encoder is the same as the motor encoders. (All four the same!) The circuit board is not soldered on and so it provides perfect repair parts for a motor encoder.
  6. My crude understanding is as follows: The brass...

    My crude understanding is as follows: The brass roller encoder is the accurate encoder. It is calibrated (and can be re-calibrated) to accurately measure the board position. The X motor encoder...
  7. Replies
    8
    Views
    412

    1. Your lines must not be closed. Use the snap...

    1. Your lines must not be closed. Use the snap grid (0.25) and drag the last dot onto the first dot until you see the cross appear.
    2. It will carve with the 1/16" carving bit by default.
    3. I just...
  8. Replies
    8
    Views
    412

    I have no idea what size you want but here is a...

    I have no idea what size you want but here is a quick attempt. I think the feather is what you want for the sides.
  9. Thread: Strange Text

    by bergerud
    Replies
    3
    Views
    290

    You have just stretched the text box and made it...

    You have just stretched the text box and made it too wide. Drag the handle to make the rectangle narrow again.
  10. Replies
    4
    Views
    309

    Just move it by hand. Whether the machine is off...

    Just move it by hand. Whether the machine is off or on does not matter. (It is a little easier to move if it is off.) Move it anywhere you want and leave it anywhere you want. It does not matter.
  11. Replies
    4
    Views
    309

    I think you can move the spindle anywhere you...

    I think you can move the spindle anywhere you like. The machine knows where the truck is and will simply return to doing whatever it was doing before the pause.
  12. I like the chalk trick. Have to give that a try....

    I like the chalk trick. Have to give that a try. I have had problems holding carbide bits in much better chuck systems than the CT split collet. Smooth carbide bits plus resonant vibrations can...
  13. Replies
    15
    Views
    1,155

    Have you disabled the file preview feature? It...

    Have you disabled the file preview feature? It can be a major cause of Designer crashing. Under the help menu - disable previews.
  14. Replies
    10
    Views
    630

    Do you notice the difference in truck resistance...

    Do you notice the difference in truck resistance to movement when the power is on Vs off. The z motor not getting power will cause an immediate stall.
  15. Replies
    3
    Views
    214

    My first thought would be something is loose....

    My first thought would be something is loose. Wiggle the bit by hand to see if there are some loose bearings on the truck. Did the hole diameters turn out right?
  16. The machine thinks that it is routing around the...

    The machine thinks that it is routing around the edge of the board (the virtual board in Designer). If your real board was the same size as the virtual board, the over routes would be in space! I...
  17. Replies
    3
    Views
    283

    The dowel diameter does not matter. One does not...

    The dowel diameter does not matter. One does not even need a dowel. One only needs a way to measure complete revolutions.

    I do not think your dowel diameter is the reason for the overshooting....
  18. Replies
    7
    Views
    401

    You need not always say NO to "stay under...

    You need not always say NO to "stay under rollers". In some cases it makes no difference, and in others, it is actually useful.

    First one needs to understand what the machine does when you say...
  19. Replies
    267
    Views
    33,610

    Glad to see you are using it! For me, it is...

    Glad to see you are using it! For me, it is standard procedure. I very rarely carve down on the belts.
  20. Replies
    7
    Views
    316

    Maybe you have the texture set to none? view -...

    Maybe you have the texture set to none? view - texture - wood
  21. Replies
    23
    Views
    5,119

    This is a very old thread. Post the mpc you want...

    This is a very old thread. Post the mpc you want to cut and see if we can help.
  22. Replies
    8
    Views
    683

    The hole Floyd is referring to would be a hole...

    The hole Floyd is referring to would be a hole drilled by the bit through the touch point next to the brass roller. If this touch point gets drilled through, the bit touches too low and then later...
  23. Replies
    8
    Views
    683

    If the bit is hitting the right edge of the sled...

    If the bit is hitting the right edge of the sled instead of dropping down beside the sled, I would think the sled was not measured to be as wide as it really is. Watch where the machine initially...
  24. Replies
    27
    Views
    2,780

    The reason you did not need the touch holes was...

    The reason you did not need the touch holes was because the carving was not deeper than 1/2". In this case the machine does not bother to measure the board thickness. Now for the bad news. The touch...
  25. Replies
    140
    Views
    25,931

    By hand with a small square file.

    By hand with a small square file.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4