Search:

Type: Posts; User: DickB; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Thread: 18 pin cable

    by DickB
    Replies
    15
    Views
    1,006

    I have not found an exact replacement in stock -...

    I have not found an exact replacement in stock - most are much smaller in length. I have a few suggestions.

    Samtec offers a 20-pin cable in the length that you need. I would try trimming one with...
  2. Thread: 18 pin cable

    by DickB
    Replies
    15
    Views
    1,006

    What I am asking is the cable a "Type A" or "Type...

    What I am asking is the cable a "Type A" or "Type B" per the attached photo.

    88660

    We also need to know the pitch of the contacts. If the cable is 3/4" wide, with 18 contacts the pitch should...
  3. Thread: 18 pin cable

    by DickB
    Replies
    15
    Views
    1,006

    Are the contacts on the same side of the cable,...

    Are the contacts on the same side of the cable, or opposite sides?
  4. Thread: 18 pin cable

    by DickB
    Replies
    15
    Views
    1,006

    A cable may be available through electronics...

    A cable may be available through electronics suppliers. Please measure the exact length and width of the cable, and if possible the spacing between conductors (will likely be in metric). Also a...
  5. FYI. I have not used one myself. 88659

    FYI. I have not used one myself.

    88659
  6. Replies
    14
    Views
    968

    Stimulus check? ;)

    Stimulus check? ;)
  7. Replies
    14
    Views
    968

    It can reduce carve time, and yes the X and Y...

    It can reduce carve time, and yes the X and Y work together with Centerline.

    The attached examples are on a 12" x 6" board. Centerline time is 3:34 and Raster 6:31.

    88650 88651


    If...
  8. Replies
    14
    Views
    968

    I would suggest Centerline and Conforming Vectors...

    I would suggest Centerline and Conforming Vectors for signs as suggested by lynnfrwd. I would hold off on purchasing Pro until you find that you need it, unless budget is not an issue. That said,...
  9. Replies
    9
    Views
    600

    After pressing 7 (Measure), press 1 to select...

    After pressing 7 (Measure), press 1 to select Length (nothing will happen until you select Length or Width). If the board moves, the controller is probably OK and it is either a bad display or a bad...
  10. Replies
    9
    Views
    600

    If the controller were bad I would think the...

    If the controller were bad I would think the machine would not even go through the homing process. I would pretend everything was OK and try an operation such as Measure to see if it works. I can...
  11. Replies
    13
    Views
    739

    It seems to be an issue with Designer Pro. It...

    It seems to be an issue with Designer Pro. It works for me in Designer Basic, but not Pro - I get the same result as you no matter the font.

    As a workaround, you could break the date into 5...
  12. Replies
    13
    Views
    739

    I don't have a "bullet" on my keyboard. How are...

    I don't have a "bullet" on my keyboard. How are you entering it?
  13. Replies
    14
    Views
    968

    Yes, please elaborate on what you would like to...

    Yes, please elaborate on what you would like to do in your projects.
  14. Replies
    4
    Views
    1,780

    You can use raster and the Invert tool. Best...

    You can use raster and the Invert tool. Best with no feather and shallow depth.
  15. Replies
    5
    Views
    887

    Use the Flip to other side of the model tool, it...

    Use the Flip to other side of the model tool, it will change from pink to brown and you can proceed.
  16. Replies
    5
    Views
    887

    Can you post the image that you imported?

    Can you post the image that you imported?
  17. Replies
    3
    Views
    487

    Run a board sensor test:...

    Run a board sensor test: http://support.carvewright.com/checking-and-cleaning-the-boardsensor/

    Post results.
  18. Replies
    5
    Views
    851

    This is the best technique to easily "carve" a...

    This is the best technique to easily "carve" a photo in wood. I use quotation marks because you're not really converting a photo to 3D, but creating slightly higher (lighter) and deeper (lower)...
  19. Replies
    7
    Views
    1,115

    ER11. Many collet sizes available. I have one...

    ER11. Many collet sizes available. I have one similar to this for my CarveTight spindle: ...
  20. Replies
    12
    Views
    1,422

    I would not go that deep - .125" would be plenty.

    I would not go that deep - .125" would be plenty.
  21. Replies
    12
    Views
    1,422

    Please post the original image (or a link) and...

    Please post the original image (or a link) and your mpc.
  22. Replies
    52
    Views
    11,282

    Kinda quiet around here. I guess I am partly to...

    Kinda quiet around here. I guess I am partly to blame, as I haven't posted updates on this project for a while. The body is basically finished. The last items that I finished were the rocker...
  23. Thread: Mac problems

    by DickB
    Replies
    11
    Views
    2,217

    Looks like you are running different versions of...

    Looks like you are running different versions of Designer.
  24. Replies
    5
    Views
    980

    Looks good! Are you going to join the halves...

    Looks good! Are you going to join the halves back together?
  25. Replies
    5
    Views
    980

    As I posted on facebook, I would sue Jog to...

    As I posted on facebook, I would sue Jog to center. Mark the center of your rectangles on the slab. Make your virtual boards the same size as your rectangles. Place text as you want to have it...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4