Search:

Type: Posts; User: Digitalwoodshop; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.05 seconds.

  1. Replies
    10
    Views
    265

    I like the Shim Idea posted above.. That is what...

    I like the Shim Idea posted above.. That is what I would do.
  2. Replies
    32
    Views
    614

    What are your sled tails length. Sure looks like...

    What are your sled tails length. Sure looks like 3.5 inches.... I always do 4 inches... 3.5 inches lets the board "Tighter" on that roller "EDGE"... I like the extra 1/2 inch...

    I would try the...
  3. Replies
    5
    Views
    384

    Good Job !!!!

    Good Job !!!!
  4. Replies
    8
    Views
    328

    Sorry to just throw out the 7 inch rule of wood...

    Sorry to just throw out the 7 inch rule of wood without explaining it.... So here it goes.... The Readers Digest Version...

    So the top black rubber rollers are 7 inches apart. And the bit is...
  5. Replies
    8
    Views
    328

    Yep, the 7 inch rule of wood....

    Yep, the 7 inch rule of wood....
  6. Replies
    14
    Views
    1,411

    If you still have it crank head down on a sheet...

    If you still have it crank head down on a sheet of white paper and use sensor data to see the value. 156 perfect 100 dirty window.
  7. Replies
    3
    Views
    360

    A whole list of things can cause this.... The 2...

    A whole list of things can cause this.... The 2 lead screws have been known to strip the nut on top. Sawdust caked in the lead screw can jam the head. The 4 smooth posts could have dry grease on...
  8. Replies
    14
    Views
    1,411

    I mentioned it on the CarveWright Facebook Page....

    I mentioned it on the CarveWright Facebook Page. Might help. That is a great price.

    AL
  9. Replies
    6
    Views
    524

    And speaking of disappearing TEXT... Some fancy...

    And speaking of disappearing TEXT... Some fancy text, the far left side of some fancy first letters will be missing from the carve... In that case use a TAB 1 space then start your text.
  10. Replies
    6
    Views
    247

    You can overlay a shallow carve region like a...

    You can overlay a shallow carve region like a square or any shape on top of your text to help connect the script text or like I do to make a base for the BEAR... Then Outline and assign a cut bit for...
  11. Impressive !!!!

    Impressive !!!!
  12. Replies
    2
    Views
    236

    Aaron B, Welcome Back. I see your last posts...

    Aaron B,

    Welcome Back. I see your last posts were from 2012. As I understand it, you are looking for the latest free version of 1.184. And likely you have found it....

    I use only the Free...
  13. That Error came up when we changed from the 18...

    That Error came up when we changed from the 18 pin FFC Cable to the 14 pin Cable and changed the circuit board on both ends.
  14. Replies
    18
    Views
    1,582

    Sawmill Creek has a forum that I visited often...

    Sawmill Creek has a forum that I visited often but not lately. Lots on working with Acrylic. I even got in on a group purchase of some flame polishers from China... They did a 2nd buy....
  15. I use a ROCK Chuck that is 1/4 inch. It was the...

    I use a ROCK Chuck that is 1/4 inch. It was the first after market chuck to replace the QC. No longer made, it had a 1/8, 1/4, and 1/2 inch screw on head. I use 1/4 inch so this works for me.

    As...
  16. The bit holder as seen in the picture is from...

    The bit holder as seen in the picture is from Roto Zip. Used with a Dremel Type small router to cut sheet rock and the likes. Found at my local lumber yard where they sell roto zip bits. The Roto...
  17. My take on cutting the Corian is to use a 1/16th...

    My take on cutting the Corian is to use a 1/16th Circuit Board End Mill Bit.. Not the 1/8 inch cutting bit... And lay out your cuts then select the 1/4 inch round nose bit. BUT you will insert a...
  18. Replies
    20
    Views
    3,969

    Back in the day when we were new to the...

    Back in the day when we were new to the machines... Chris and I met another carver from Up State New York called Chisel me Timbers in a Church Parking lot along the Delaware River where I knew the...
  19. Replies
    20
    Views
    3,969

    A BIG BUMP.... Floyd and I were chatting with...

    A BIG BUMP.... Floyd and I were chatting with ChrisAlb last night on Facebook. Floyd posted this link to his thread... Pretty nice work... At the time it was one of the longest carving projects that...
  20. Interesting take on Encoders. Great Video too.

    Interesting take on Encoders.

    Great Video too.
  21. Did not know that... :) AL

    Did not know that... :)

    AL
  22. Brad, I wish you would post this same...

    Brad,

    I wish you would post this same question in the Facebook Carvewright Group. The reason is that the Owner of LHR sometimes posts some very interesting replies to our Technical Questions...
  23. Replies
    7
    Views
    385

    I have not opened any of the others I have.... 7...

    I have not opened any of the others I have.... 7 machines now... But i will add that to the next preventive maintenance to all for a one time look. The last one I just could not pass it up......
  24. Replies
    7
    Views
    385

    A few years ago I was pushing the machine hard in...

    A few years ago I was pushing the machine hard in August and I blew a Controller Computer... Went Dead... Had another controller so I swapped it out... Worked like a charm... Put the old controller...
  25. Replies
    18
    Views
    1,621

    It's a Holiday Weekend.... but a heads up on...

    It's a Holiday Weekend.... but a heads up on Monday... The thumbs up is broke.... I can live without it.... Just wanted to give a Thumbs Up to this thread and post... I am a Power Supply guy.......
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4