Search:

Type: Posts; User: fwharris; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.04 seconds; generated 3 minute(s) ago.

  1. Replies
    32
    Views
    614

    As per the CW recommendations there needs to be...

    As per the CW recommendations there needs to be some play/movement in the rod.
  2. Thread: Spindle shaft

    by fwharris
    Replies
    4
    Views
    128

    I took the motor out of the machine and sprayed...

    I took the motor out of the machine and sprayed some wd-40 into the end of the motor. Then I used some pliers to grab the shaft right at the motor end twisted/pried to break it loose. Once out I did...
  3. Thread: Chef pattern

    by fwharris
    Replies
    8
    Views
    234

    Oscar did all of the hard work! ;)

    Oscar did all of the hard work! ;)
  4. Thread: Lithopanes

    by fwharris
    Replies
    2
    Views
    109

    No it is not needed but you do get a great...

    No it is not needed but you do get a great preview with Pro. Just follow the instructions in the tips n tricks newsletter for carving lithophanes.
  5. Thread: Chef pattern

    by fwharris
    Replies
    8
    Views
    234

    https://clipartstation.com/wp-content/uploads/2018...

    https://clipartstation.com/wp-content/uploads/2018/09/chef-clipart-female-7.jpg

    https://www.sccpre.cat/show/iwJowwi_cook-clip-art-vector-holding-a-menu-cook/
    ...
  6. Replies
    1
    Views
    95

    When you say YES to staying under the rollers the...

    When you say YES to staying under the rollers the machine will ADD 7" to your design size length and look for a board at least that long. If it sees the board even a small amount shorted than...
  7. Replies
    10
    Views
    265

    You can verify the depth of cut by placing the...

    You can verify the depth of cut by placing the mouse pointer on an area on the board and viewing the depth of the area in the bottom left hand corner in Designer. There will be 3 different numbers....
  8. Replies
    32
    Views
    614

    115 lbs is to high. You stand the chance of...

    115 lbs is to high. You stand the chance of stripping the X drive gears with it being that high.
  9. Replies
    4
    Views
    141

    An ah sh*t moment for sure, been there done that....

    An ah sh*t moment for sure, been there done that. You can not resume the carving but you can recover it.

    Draw a rectangle over the area that has been carved but leave the rectangle just a bit...
  10. Replies
    32
    Views
    614

    It looks to be off in the X axis and to me the...

    It looks to be off in the X axis and to me the full carving is off in the X axis direction.
  11. Thread: font sizes

    by fwharris
    Replies
    8
    Views
    328

    It sounds like you need to start from the...

    It sounds like you need to start from the beginning with some basic design help. This link will take you step by step for making proper designs for carving and cutting them out and how to set up the...
  12. Thread: font sizes

    by fwharris
    Replies
    8
    Views
    328

    Did you get any message about scaling? Are...

    Did you get any message about scaling? Are carving the text and then trying to cut them out?
  13. Thread: Acrylic

    by fwharris
    Replies
    7
    Views
    377

    Drag bit.......

    Drag bit.......
  14. Thread: Acrylic

    by fwharris
    Replies
    7
    Views
    377

    Joe Lovchik has said he has used one. I think you...

    Joe Lovchik has said he has used one. I think you need to un do the flex shaft.
  15. Replies
    112
    Views
    13,219

    Nice looking set!

    Nice looking set!
  16. Replies
    2
    Views
    163

    The link to it.......

    The link to it.... http://support.carvewright.com/carving-jigs-carrier-boards-sleds-and-rails/

    I went there to look it up but it was not showing in the list on the page so I did a search and find.
  17. Replies
    2
    Views
    163

    Yes there is a tips and tricks newsletter for...

    Yes there is a tips and tricks newsletter for building a jig/sled/carrier board for carving. It can be found on the CW site in the support section.
  18. Replies
    6
    Views
    443

    I do not have any machine measuring problems with...

    I do not have any machine measuring problems with my LED lighting system in the machine. 12v 1amp power source.
  19. Replies
    8
    Views
    860

    You have already done the other things I would...

    You have already done the other things I would suggest doing. Sorry as I do not know what else to mention.
  20. Replies
    8
    Views
    860

    File preview is only in the Pro version. Try...

    File preview is only in the Pro version. Try increasing your rendering cache size. It is found in the "preference" settings under the "edit" tab. Default is 16MB, try 256mb or higher.

    If you...
  21. Well not exactly for me... Imported as is, no...

    Well not exactly for me... Imported as is, no changes made. After on the board, set feather to "none" and bit optimization to "best" but still had the line boundary.

    Next I changed the depth from...
  22. I "think" the background he is talking about is...

    I "think" the background he is talking about is what I have marked in red... Since the image/pattern itself is in a dish it is lower than the outer background area around it. When trying use the...
  23. The pattern is in a dish so the lowering function...

    The pattern is in a dish so the lowering function does not work in the import window. Contact the maker to see if they can remove the background rectangle.
  24. Replies
    6
    Views
    586

    Set your project board thickness in designer to...

    Set your project board thickness in designer to 0.250". This tells designer when you set your cut path to only cut .250" deep.
  25. Replies
    6
    Views
    586

    After you get the image into designer to make it...

    After you get the image into designer to make it a pattern, put the pattern on your board and size it to what you want. Next do an "outline" of the pattern and use the cut path tool. If you do not...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4