Search:

Type: Posts; User: Digitalwoodshop; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.09 seconds.

  1. I bet that is the one he wants. I learned a few...

    I bet that is the one he wants. I learned a few tricks from that one...

    AL
  2. Replies
    4
    Views
    242

    This is making it's way through many Military...

    This is making it's way through many Military Facebook Pages this weekend. :)

    AL Who. US NAVY Retired. FCC(SW) :)
  3. Replies
    5
    Views
    158

    Bigger Text will require a V90 Bit.

    Bigger Text will require a V90 Bit.
  4. Replies
    5
    Views
    163

    Great Idea... Thanks :)

    Great Idea... Thanks :)
  5. Replies
    5
    Views
    163

    I have attempted to do Name Tags with the CW. The...

    I have attempted to do Name Tags with the CW. The Resolution of the Encoders is too loose.... As in it is not fine enough to do small text.

    I posted part of this on the Facebook Page and asked for...
  6. I don't have a good answer for this question... ...

    I don't have a good answer for this question... It will be a trick to get the split collet in the right position where the bit wedge is effective in holding it tight. If you got the collet turned...
  7. Replies
    18
    Views
    2,101

    Only on April Fools DAY.... in 2008... :) ...

    Only on April Fools DAY.... in 2008... :)

    AL Who... Troublemaker...
  8. Replies
    3
    Views
    130

    Lots of paper towels to catch the run off.... And...

    Lots of paper towels to catch the run off.... And soak the rags in water so no Spontaneous Combustion... I was doing Poly with a rag years ago out on my deck. Got a phone call... Dropped my rag on...
  9. Replies
    18
    Views
    2,101

    Guy T, You may have missed it.... The LASER...

    Guy T, You may have missed it.... The LASER OPTION was available for a short time but could only be used with the QC and the 18 pin FFC as it supplied the 14.2 Giga Watts that it needed... When...
  10. Replies
    18
    Views
    2,101

    Curious... is it the limitation of the size of...

    Curious... is it the limitation of the size of the memory card memory?

    If that was the case.... A Extended Memory, Memory Card....

    AL Who
  11. Replies
    10
    Views
    369

    My suggestion was going to be to swap the...

    My suggestion was going to be to swap the controllers thinking it was a Servo Driver.... Glad you made progress.
  12. Replies
    0
    Views
    101

    CW Carving to make money.

    So I was on a Laser Engraving FB Page participating in a thread on how to make Motel Key Tags of the past for a Laser User having a new request. I chimed in about how I make my Fire Tags. This lead...
  13. Replies
    7
    Views
    255

    That would be a fun test with a Dial Indicator...

    That would be a fun test with a Dial Indicator and a video camera.... So you could freeze frame it later to see the results.
  14. Replies
    3
    Views
    88

    I don't understand what you are asking?

    I don't understand what you are asking?
  15. Replies
    1
    Views
    117

    A few things can cause the X Axis to stall. That...

    A few things can cause the X Axis to stall. That is the Sand Paper or Rubber Belts.

    1. Head Pressure too tight.

    2. A Tapered Board

    3. The right side guide in the middle of the machine is TOO...
  16. Replies
    7
    Views
    263

    I use Place on END or Corner. Corner comes up...

    I use Place on END or Corner. Corner comes up when the physical board is wider than the Designer Board.

    Look at your screen in Designer. The top is the Keyboard side of the board or the Brass...
  17. Replies
    4
    Views
    118

    Is that only after they go through the Pattern...

    Is that only after they go through the Pattern Depot? This is an area I don't know much about.
  18. Replies
    63
    Views
    4,711

    First thing to do is put a 1/8 inch bit in the...

    First thing to do is put a 1/8 inch bit in the machine and move the truck over to the keypad side and lower the head. LOOK and see if the bit drilled a hole in the brass roller PLASTIC HOLDER. IF it...
  19. Replies
    8
    Views
    451

    AND Comma.... I have been known to be WRONG a few...

    AND Comma.... I have been known to be WRONG a few times.... SO based on your reply we will jump like a group of Brook Trout in a small pool when a Grass Hopper falls in... This looks...
  20. Replies
    8
    Views
    451

    Put a 1/8 inch bit in the machine and move the...

    Put a 1/8 inch bit in the machine and move the head all the way to the keypad side and manually slide the head down. Look where it touches the black plastic that holds the brass roller. Look and see...
  21. Replies
    12
    Views
    625

    Next time call up the pressure rollers in options...

    Next time call up the pressure rollers in options and sensor data and crank down on a board and watch the status of the switches. Dust builds up in the resting state of the rollers and does not let...
  22. New LASER Bit could SOON be a option for the CarveWright.

    Hot off the press yesterday on April 1st is a HOT NEW TOOL.... A LASER SABER SAW....

    Can't wait until it is adapted to the CW.

    Designer LASER EDITION is in the works...

    See here.... Check...
  23. Replies
    6
    Views
    331

    Then we have Pooh Bear.... From 2008.

    Then we have Pooh Bear.... From 2008.
  24. Replies
    15
    Views
    863

    That would be ME.... I am 1.182 and would have...

    That would be ME.... I am 1.182 and would have just updated and crashed the program. Thank You for the heads up Lynnfrwd.

    Where can I find the improvements with 1.188?

    :) AL software in not...
  25. Replies
    32
    Views
    4,269

    That is a GOOD Question.... How many hours on my...

    That is a GOOD Question.... How many hours on my trucks... I have had Truck Trouble over the years because I was able to send a few to TIM to keep on hand when he wants to test his Porter Cable...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4