Search:

Type: Posts; User: bamaman315; Keyword(s):

Page 1 of 12 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    6
    Views
    675

    no I have a dust collector attachment that came...

    no I have a dust collector attachment that came from carvewright , hooked it to my dust collector hose
  2. Replies
    6
    Views
    675

    Not yet only have 38 1/2 hours on the machine, it...

    Not yet only have 38 1/2 hours on the machine, it is out of warranty due the age , I have had it for about 2 years
  3. Replies
    6
    Views
    675

    cut motor issue

    I was carving a rotary lamp pattern , I got a check cut motor message. I checked it and did not see any visible issues with it , so I closed the cover and hit the enter key. The motor started up but...
  4. Replies
    4
    Views
    490

    what would cause the machine to carve a rotary...

    what would cause the machine to carve a rotary pattern but gives you issues when you go to a regular carve pattern , ( coin bank )
    When I load the cutting bit it will not go to the bit plate , but...
  5. The truck does have some resistance when the...

    The truck does have some resistance when the power is off , I push it all the way to the right till the bit plate pops out.
    I have cleaned the rails and the rollers and still has resistance.
  6. No 2 different machines with different problems

    No 2 different machines with different problems
  7. differnet machine, will not get past loading the cutting bit

    I am trying to carve the coin back project with this machine also, this machine will not get past the option of loading the cutting bit , wont even go over to the bit plate. Any ideas?
  8. bit not going all the way down to the bit plate

    I am trying to carve the coin bank pattern , when it comes to load the cutting bit it will not go down and touch the bit plate and when it comes back to key pad side the bit will not go down and...
  9. Replies
    4
    Views
    490

    I do have an older machine and I had 3 washers on...

    I do have an older machine and I had 3 washers on it, I had to use all 3 to get head pressure to 80lbs. Thank you for your advice !
  10. Replies
    4
    Views
    490

    Head Pressure too Low

    I have gone through the whole process in the procedure to adjust the pressure. Before I started my head pressure was around 50 lbs. After going through the process to adjust machine , I got the...
  11. Replies
    11
    Views
    1,919

    yes I am using 40 pipe

    yes I am using 40 pipe
  12. Thread: Please Help

    by bamaman315
    Replies
    5
    Views
    1,138

    yes it is Schedule 40

    yes it is Schedule 40
  13. Thread: Please Help

    by bamaman315
    Replies
    5
    Views
    1,138

    how do you tell? I have used this same pipe for...

    how do you tell? I have used this same pipe for other lamps and it works great. I did try and carve it again but the picture got compressed.
  14. Thread: Please Help

    by bamaman315
    Replies
    5
    Views
    1,138

    Please Help

    I have a friend that lost her mom and dad within 3 months of each other. I want to make her a rotary lamp with her parents on it. I have the program and I have entered all the settings in the...
  15. Replies
    11
    Views
    1,919

    When you open up your project look under board...

    When you open up your project look under board settings and see if the right bit is selected. I was under the empression that it automatically picked the right bit , but I was wrong. I am about to go...
  16. Replies
    11
    Views
    1,919

    Rotary lamp settings

    I have tried to go a lamp project and have used the settings in the instructions, problem is it carves too deep and ends up carving all the way through the pvc pipe.
    any ideas how to correct this?
  17. That was what was wrong, The wrong bit was...

    That was what was wrong, The wrong bit was selected. I was under the impression that when you loaded a rotary pattern it would automatically select the right bit.
    I guess you can still learn...
  18. I am using the long carving bit that came with...

    I am using the long carving bit that came with the rotary jig.
  19. Replies
    3
    Views
    486

    Thank you , I did try and measure a board the was...

    Thank you , I did try and measure a board the was 20 3/4 inches long , but machine said it was over 21 1/2 inches long. any ideas?
  20. Replies
    3
    Views
    486

    Coin bank pattern

    I have carved this pattern so many times but the last time I tried it the pattern came out smaller. I have always used a 24 inch long board with no problems. This time it came out smaller, I did...
  21. Carver works fine with regular project but gives z axis stall while setting up rotary

    I had been trying to do a rotary lamp project but when the bit goes to the right and hits the bit plate it gives me the z axis error message. I tried it on two of my machines with the same results. I...
  22. Replies
    1
    Views
    828

    Turkey Fan Tail Mount

    My computer crashed and I lost my pattern that I had for the Turkey Fan Tail Mount, Does anyone have one to share ?
  23. Replies
    1
    Views
    1,029

    Make America Great Again

    I saw this paddle online , I would like to make one but I can not get the pattern to come out right. Any help would be awesome. Thanks in advance.
  24. cone chalk holder for a game room pool table

    Does anyone know where I can get a good pattern to make a chalk holder for the cone shape chalk ?
  25. Replies
    1
    Views
    1,356

    wolf pattern

    Does anyone have a good wolf pattern to share ?
    Thanks in advance .
Results 1 to 25 of 289
Page 1 of 12 1 2 3 4