Search:

Type: Posts; User: darth woodilust; Keyword(s):

Page 1 of 2 1 2

Search: Search took 0.00 seconds; generated 40 minute(s) ago.

  1. Replies
    25
    Views
    5,645

    I replaced x termination board Sunday. I...

    I replaced x termination board Sunday.

    I spoke with tech support about this issue when it began several weeks ago. They suggested that the motor needed replacement due to possible encoder issue....
  2. Replies
    25
    Views
    5,645

    Taken this machine apart inside and out many...

    Taken this machine apart inside and out many times. Biomedical engineer for thirteen years. This is pretty basic for me mechanically.
    Already checked gears. All operational with no missing teeth....
  3. Replies
    25
    Views
    5,645

    Bypassed cover switch and cut motor is now...

    Bypassed cover switch and cut motor is now operational but still no luck with x stall. New motor and new x termination board. Anyway to run a diagnostic on the controller?
  4. Replies
    25
    Views
    5,645

    Replaced x termination board. No difference other...

    Replaced x termination board. No difference other than now my cut motor doesn't spin.
  5. Replies
    25
    Views
    5,645

    Motor has been tested without any resistance (...

    Motor has been tested without any resistance ( gears drive to belt feed removed) I do not believe it is friction as I have stated;the motor has also been tested outside the machine with no failures....
  6. Replies
    25
    Views
    5,645

    The x motor does have an encoder which is why I...

    The x motor does have an encoder which is why I bought a new motor. I tested the old motor before making the purchase and the motor worked fine in my outside the machine test. Thought maybe it was...
  7. Replies
    25
    Views
    5,645

    The x motor was replaced. Carvewright guys on the...

    The x motor was replaced. Carvewright guys on the phone said it was probably a bad encoder. I put the new x motor in today and I have the same problem. X motor starts then stops immediately. This...
  8. Replies
    25
    Views
    5,645

    The gears are good. Again gears not engaged for...

    The gears are good. Again gears not engaged for testing purposes. Motor works with outside power source. When the machine controls the motor a start and quick stop
  9. Replies
    25
    Views
    5,645

    I just updated the software for the first time in...

    I just updated the software for the first time in years a few weeks ago.
  10. Replies
    25
    Views
    5,645

    so after letting myself cool down after the...

    so after letting myself cool down after the aggravation i felt from this machine giving me problems again after barely 100 hours carve time, i turned on machine and preformed a x axis motor test it...
  11. Replies
    25
    Views
    5,645

    the error message is e04-0293. again motor starts...

    the error message is e04-0293. again motor starts then stops with zero resistance as i do not have any gear installed. when motor is tested outside of machine (different power supply) it spins fine
  12. Replies
    25
    Views
    5,645

    yes sir the x axis that drives belt feed. checked...

    yes sir the x axis that drives belt feed. checked head pressure. lubed. disassemble and cleaned machine top to bottom. removed x axis motor and it tested fine and turned with no noise.
  13. Replies
    25
    Views
    5,645

    x motor stall

    long to short, keep getting x motor stall. it will start then immediately stop. disassemble machine. removed x motor from the belt feed gears. tested motor. same response. it starts but stop quickly....
  14. Replies
    19
    Views
    77,658

    Thanks for the link. I definitely will!

    Thanks for the link. I definitely will!
  15. Replies
    19
    Views
    77,658

    Hi! Really cool work. I would like to experiment...

    Hi! Really cool work. I would like to experiment with this octopus. Can you send me your design? Thanks for the inspiration either way.
  16. Replies
    3
    Views
    2,332

    I disconnected the servo motor. tested good....

    I disconnected the servo motor. tested good. reinstalled. worked fine. poltergeist?
  17. Replies
    3
    Views
    2,332

    error e04 0293 x axis

    keep getting this error. I measured a piece of wood and went to start a carve. the x axis starts for just a second then stops and gives error message. any ideas?
  18. Replies
    2
    Views
    1,307

    Thank you! That's it.

    Thank you! That's it.
  19. Replies
    2
    Views
    1,307

    pattern sharing help

    I lost all of my patterns due to pc failure. I got a ton of them from a link on here a couple of years ago. Anyone know the link?
  20. Replies
    1
    Views
    3,088

    0 depth

    I got a warning that the cuts were too wide when uploading but they are at zero depth do I still need a jig?
  21. Replies
    10
    Views
    3,141

    i hear the clicking when the rollers are...

    i hear the clicking when the rollers are initially deppressed. also i went through this section of the manual and blew out the rollers while moving them up and down earlier today while cleaning
  22. Replies
    10
    Views
    3,141

    ok i just did the paper test and the reading went...

    ok i just did the paper test and the reading went up to about 130. i noticed a few things while doing this;1 when i prompted to measure board the z axis moves over to the edge of the board when i...
  23. Replies
    10
    Views
    3,141

    today i relubed everything checked the sensors...

    today i relubed everything checked the sensors and everything pans out rollers compressed/deppressed . I got a consistent board reading of 65 when lowered on wood. still got load board errors and...
  24. Replies
    10
    Views
    3,141

    Also I checked the pressure and i get 70-75...

    Also I checked the pressure and i get 70-75 pounds regular
  25. Replies
    10
    Views
    3,141

    load board error

    I just carved a jignow when i load my corian for a litho i keep getting load board error. i tried loading different pieces of wood and it eems like it will not register 3/4 inch wood but it will on...
Results 1 to 25 of 28
Page 1 of 2 1 2