6909969100
I had finished a carving, shut the machine off. went to vacuum the dust up. it shocked me with a small arc from the machine to the nozzle on the vacuum
when i loaded the card and went to...
Type: Posts; User: lynchburgbull; Keyword(s):
6909969100
I had finished a carving, shut the machine off. went to vacuum the dust up. it shocked me with a small arc from the machine to the nozzle on the vacuum
when i loaded the card and went to...
thanks guys
it looks like it might be the board tracking sensor. Ive been working with Steve on this issue also. Im going to replace it and see what happens
thanks
ok continuing with this issue....
Ive installed a new board sensor, now getting reading of 120+ but....E03-0400 "edge detection failed". has now surfaced. I have checked the compression rollers,...
Ive done the white paper check on the sensor. in the neighborhood of an 80 give or take.
put a new sensor in .....same numbers
any ideas folks ?
thanks
Greg
thanks guys.
hi folks,
ok Im trying to get the CW running again. latest issue is that it is not measuring correctly.
I put a 3/4" pice of pine in, lowered the head. selected 7 then length. first it said...
yep I did I checked it after this happened. Its between 75-80, I checked it 5 times. ran the head up all the way and back down each time and made sure it clicked 3 times each time .............just...
Thanks Floyd . I will reinstall everything tomorrow night and double check it
I had that happen before too. that wasnt the case this time. this is the second time for the belt and the gear. which broke first and caused the other Im not sure. both times the belt has completely...
ok the new x gear assembly is in turned freely. x motor turned freely, right side belt( facing keyboard of course) turned freely. left side belt turned freely
after assembly up to the left side...
ok here is the issue....
the sandpaper belts keep separating, only on one side. the left side. Head pressure is 78-82 checked it 5 times.
this is causing, at least I think it is causing the X...
I will thanks
anyone having issues with the belts? I have had 2, from the same set, separate on the seam. One had less than 6 hours on it.
those look good for large areas but I do a lot of small detail things64492 Im not sure it would get int the crevasses with out sanding down the detail
ah thanks for the heads up Al
thanks, Ill look at it and send it to the client and see if she likes it. I knew the one was a pay font, didnt know the other one was out there. thanks again
The main font is called Zapfino, and the second is Gabriola. Does anyone have these fonts available and can create a pattern for me with them. its real simple. I just dont have the fonts. here is the...
thanks
I appreciate it
Hi folks,How can I make text not carve so deep. Im doing 90 degree bit, Script MT bold font, and centerline.
will decreasing the height and lenght of the text make it shallow?t
thanks
Greg
Dremel 511E & 512E EZ Lock Coarse Grit and Medium Grit and fine Finishing Abrasive Buffs,
they do not last at all. I used them up ( all 4 of them ) in a matter of 10 minutes sanding black willow. I...
How about this........Ive been carving a tree of life for awhile now. 60012A while back was the first time I saw it but what it did was almost like it carved it twice but shifted about 1/4" to the...
The site looks good Clint. Good Luck with it.
Thanks again Ed.
This link is to a hard drive enclosure that Chief sent me. If by chance you have an old computer with the hard drive intact but the rest of it dead, then this can be a back up...
do you have a video on that Bud ? or one close to that ?
hey folks,
I do a lot of boxes. I need to ba able to 45 the ends only of the sides. other than cutting the board to the width I need and edge routing..................does anyone have a trick to...