Search:

Hi, I'm having a problem with the bit not always cutting at the set depth. It runs through the set up procedure ok but then starts cutting maybe 1/16th" above or sometimes just barely touches the...

Yes, really loud. I think you may be right bergerud. The sound, I'm pretty sure is coming from the motor and you're right- the plastic on the motor is cracked. I know it's cracked where the small...

Hi, I'm having a problem with the cut motor. When it goes through the set up procedure before a project, you hit the enter button then it tests the motor for a few seconds- the motor has an loud...

I managed to get the head level. Then I needed to repair the plastic base where the screw goes in to hold up the shaft. I tried to JB weld the broken piece but that didnt work to well. So I made a...

Ok guys, thanks I will try loosening the post bolts, take off the shaft. Let you know if it works. If it does I will have to find a way to hold the shaft up on the side where the plastic broke

Tried the hole on the jack rod but that wont work. The head is too far out of level. No brute forced used and it wasnt too high. The head always went up and down easily. This happened when I noticed...

When you say loosen everything up,, such as? Take the bolts out of the post bottom and top? Yeah the plastic broke off where the screw goes in to hold the shaft. put a metal brace across it then...

When you say loosen everything up such as?

Hi. I noticed that the head wasnt raising right. I took off the bottom and found the plastic where the retaining screw goes in to hold the shaft that raises the head was broke on the opposite side...

If the capacitor is scraped off how do you fix it?

Yes I blew it out at 80-90 psi still 46, I took it out and gently blew it out and cleaned it, still 46

I replaced the board sensor 2 months ago. I cant get it to read above 50. I have cleaned it, taken it out and cleaned it but cant get it to read above 50, stays around 46 no matter what I do. I put...

No I'm not getting any errors. I checked the head pressure, initially it was about 40-50lbs. I lubed the posts but couldn't get much more out of it. If I placed my hand on the top of the head as I...

I replaced the board sensor, placed a work piece in and checked the sensor reading before running a project. It would not go above 100. The board is a lighter color (tan). What should a new board...

Ok I'll check that. It did work for one piece then wouldn't work. I had to keep trying several times, it would do what I described then it worked once then again couldn't get it to work.

I managed to get the sensor up to about 108-110. The truck moves across the rail to the opposite side of the keypad but doesn't touch the bit to the touch plate, instead it goes down and stops about...

Ok, I'll check that. I have taken the sensor out. How does the window come out?

I used the wood I normally use, a light tan pine. Head cranked down.

I installed a new board sensor a few days ago. I checked the reading when I installed it- it read over 150. Now I cant get it much above 90. I blow it out, removed and cleaned it but still same...

Checked the bolts on the bottom of the posts and all four were loose. The top ones were a little loose as well. Seems to be working ok now. Thanks guys for the great advice, much appreciated.

I have replaced the gears at some point but I'll check them. I can move the belts with the palm of my hand but they don't move easily, I need to apply some pressure but they do move.
l'll check the...

When starting a project, the machine measures the board and as it moves it becomes very erratic, slows down then speeds up. Sometimes it jerks back and forth fast then stops. I have the sanding belt...

The threaded hole that the tie rod screw/washer goes into that secures the tie rod cracked on the key board side. This caused the head to go out of level. I fixed the problem and leveled the head by...

I finally found the problem of breaking bits. I wasn't able to see the machine running when the first two bits broke. After putting on another bit, I watched closely as the machine went through the...

From the marks on the board I would say the x axis. It initially touched down and made about a 1/16" depth mark then moved laterally about a 1/4" then broke.