Search:

Type: Posts; User: bamaman315; Keyword(s):

Page 1 of 12 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    4
    Views
    1,021

    I did not get any error message when it came to...

    I did not get any error message when it came to the cut motor, I did pull out the flex shaft and the spindles spins freely, but when the flex shaft is installed and I perform the cut motor test thats...
  2. Replies
    4
    Views
    1,021

    cut motor seems like it is locked up

    I was doing some test on my 4 machines , one of them has close door error , I changed the cover switch with no luck so I changed the termination board and nothing message is still there The 2nd...
  3. Replies
    1
    Views
    1,907

    Puck Light for PVC lamps

    I have run into a major problem, Lowes used to carry the Utilitech 2.66 in puck light that is used in the lamps. Well I found out today they are no longer available. Does anyone have a different type...
  4. Replies
    2
    Views
    1,203

    into the cpu to be askew. what does that mean?

    into the cpu to be askew. what does that mean?
  5. Replies
    1
    Views
    821

    USA FLAG free download

    Is there any reason I am getting a error message when trying to download this MPC ? It says can't be downloaded securely .
    Thanks for any help offered.:confused:
  6. Replies
    6
    Views
    1,400

    no I have a dust collector attachment that came...

    no I have a dust collector attachment that came from carvewright , hooked it to my dust collector hose
  7. Replies
    6
    Views
    1,400

    Not yet only have 38 1/2 hours on the machine, it...

    Not yet only have 38 1/2 hours on the machine, it is out of warranty due the age , I have had it for about 2 years
  8. Replies
    6
    Views
    1,400

    cut motor issue

    I was carving a rotary lamp pattern , I got a check cut motor message. I checked it and did not see any visible issues with it , so I closed the cover and hit the enter key. The motor started up but...
  9. Replies
    4
    Views
    1,077

    what would cause the machine to carve a rotary...

    what would cause the machine to carve a rotary pattern but gives you issues when you go to a regular carve pattern , ( coin bank )
    When I load the cutting bit it will not go to the bit plate , but...
  10. The truck does have some resistance when the...

    The truck does have some resistance when the power is off , I push it all the way to the right till the bit plate pops out.
    I have cleaned the rails and the rollers and still has resistance.
  11. No 2 different machines with different problems

    No 2 different machines with different problems
  12. differnet machine, will not get past loading the cutting bit

    I am trying to carve the coin back project with this machine also, this machine will not get past the option of loading the cutting bit , wont even go over to the bit plate. Any ideas?
  13. bit not going all the way down to the bit plate

    I am trying to carve the coin bank pattern , when it comes to load the cutting bit it will not go down and touch the bit plate and when it comes back to key pad side the bit will not go down and...
  14. Replies
    4
    Views
    1,077

    I do have an older machine and I had 3 washers on...

    I do have an older machine and I had 3 washers on it, I had to use all 3 to get head pressure to 80lbs. Thank you for your advice !
  15. Replies
    4
    Views
    1,077

    Head Pressure too Low

    I have gone through the whole process in the procedure to adjust the pressure. Before I started my head pressure was around 50 lbs. After going through the process to adjust machine , I got the...
  16. Replies
    11
    Views
    9,213

    yes I am using 40 pipe

    yes I am using 40 pipe
  17. Thread: Please Help

    by bamaman315
    Replies
    5
    Views
    5,324

    yes it is Schedule 40

    yes it is Schedule 40
  18. Thread: Please Help

    by bamaman315
    Replies
    5
    Views
    5,324

    how do you tell? I have used this same pipe for...

    how do you tell? I have used this same pipe for other lamps and it works great. I did try and carve it again but the picture got compressed.
  19. Thread: Please Help

    by bamaman315
    Replies
    5
    Views
    5,324

    Please Help

    I have a friend that lost her mom and dad within 3 months of each other. I want to make her a rotary lamp with her parents on it. I have the program and I have entered all the settings in the...
  20. Replies
    11
    Views
    9,213

    When you open up your project look under board...

    When you open up your project look under board settings and see if the right bit is selected. I was under the empression that it automatically picked the right bit , but I was wrong. I am about to go...
  21. Replies
    11
    Views
    9,213

    Rotary lamp settings

    I have tried to go a lamp project and have used the settings in the instructions, problem is it carves too deep and ends up carving all the way through the pvc pipe.
    any ideas how to correct this?
  22. That was what was wrong, The wrong bit was...

    That was what was wrong, The wrong bit was selected. I was under the impression that when you loaded a rotary pattern it would automatically select the right bit.
    I guess you can still learn...
  23. I am using the long carving bit that came with...

    I am using the long carving bit that came with the rotary jig.
  24. Replies
    3
    Views
    1,052

    Thank you , I did try and measure a board the was...

    Thank you , I did try and measure a board the was 20 3/4 inches long , but machine said it was over 21 1/2 inches long. any ideas?
  25. Replies
    3
    Views
    1,052

    Coin bank pattern

    I have carved this pattern so many times but the last time I tried it the pattern came out smaller. I have always used a 24 inch long board with no problems. This time it came out smaller, I did...
Results 1 to 25 of 294
Page 1 of 12 1 2 3 4