Search:

Type: Posts; User: Sconi; Keyword(s):

Page 1 of 3 1 2 3

Search: Search took 0.01 seconds.

  1. Thread: Jogging

    by Sconi
    Replies
    3
    Views
    503

    Thanks, that is what I thought I was doing but...

    Thanks, that is what I thought I was doing but haven't had any luck I'll give it another shot as it's been a little while since I tried it. Sometimes I'm able to miss the most obvious solution:???:...
  2. Thread: Jogging

    by Sconi
    Replies
    3
    Views
    503

    Jogging

    I have been looking in the users guide, and in the tips and tricks archive, and am wondering if there is a comprehensive explanation about jog to center, corner etc., been trying to make that work...
  3. Replies
    6
    Views
    545

    Thanks I'll see if I can do the math :D and give...

    Thanks I'll see if I can do the math :D and give it a try.
  4. Replies
    6
    Views
    545

    Often when I enter a new number I get a out of...

    Often when I enter a new number I get a out of calibration range error. When it will accept a number it only takes one so small it doesn't change the location significantly or at all.
  5. Replies
    6
    Views
    545

    Y offset calibration

    Spent half a day trying to re calibrate the Y offset based on the on-line instructions from the CW website. Didn't have much luck, did a forum search and found that the on line instructions don't...
  6. Replies
    1
    Views
    634

    Broken 1/8 Cutting Bits....

    I broke my second 1/8 cutting bit today, I was cutting a purchased project, in 3/4 pine, it was on it's second cutting pass when it broke. I'm going to check the cover switch to make sure vibration...
  7. Thread: Synchronicity

    by Sconi
    Replies
    36
    Views
    3,778

    That is a great clock, outstanding work sir!

    That is a great clock, outstanding work sir!
  8. Thread: Sign/key holder

    by Sconi
    Replies
    4
    Views
    519

    Many thanks to the folks who share patterns on...

    Many thanks to the folks who share patterns on the forum, I'm pretty certain that is where I got the logo.
  9. Thread: Sign/key holder

    by Sconi
    Replies
    4
    Views
    519

    Sign/key holder

    One of today's projects. It's gonna be a key holder and probably hang a couple of hats on it. Couldn't resist a tribute to my favorite toy. Once I figure out how many pegs I'll trim it to size. Not...
  10. Replies
    255
    Views
    31,574

    Thanks, that is what I needed to know!

    Thanks, that is what I needed to know!
  11. Replies
    255
    Views
    31,574

    Been using the original UCB for a while and now...

    Been using the original UCB for a while and now that I have a second machine I find myself in need of an additional one, I have been skimming through the posts on this topic and need a summary of...
  12. Replies
    3
    Views
    332

    Thanks I'll try that, the depth was incorrect on...

    Thanks I'll try that, the depth was incorrect on the original, I had changed it but apparently didn't save the change..... measure twice cut once again proves it's worth.
  13. Replies
    3
    Views
    332

    Cutting grooves too wide.....

    Working on a honey do project, and need to make some grooves 1/8 wide by 2 1/2 wide and 1/4 deep, using designer 3 I thought I made some but they cut 1/4 wide, I can work with the 1/4 wide, I think,...
  14. Replies
    3
    Views
    446

    Surprised that no one has offered any thoughts on...

    Surprised that no one has offered any thoughts on this, I'm not familiar with that error code but you might try reformatting the card under the flash management option.
  15. Thread: Desk Name Signs

    by Sconi
    Replies
    14
    Views
    828

    Very nice project.

    Very nice project.
  16. Replies
    4
    Views
    402

    Nice design, I really like those, well done sir!

    Nice design, I really like those, well done sir!
  17. Replies
    6
    Views
    438

    Christmas Gifts Done!

    Made several Christmas gifts this year, four of the Little Artists Crayon Caddy, two of the Classy Christmas Wreath, and one Christmas Candle Centerpiece all by CarveBuddy, and one domino train game...
  18. Replies
    5
    Views
    423

    Yes sir I did, it read 156 most of the time, but...

    Yes sir I did, it read 156 most of the time, but did read low once in a while, it was a fairly new sensor - a couple of months old but I replaced it just in case and nothing changed.
  19. Replies
    5
    Views
    423

    Thank you Al, I do have spare roller bearings...

    Thank you Al,

    I do have spare roller bearings and screws on hand already, had a similar experience in the past.

    The butt Floss Trick was done before and it didn't seem to make much...
  20. Replies
    5
    Views
    423

    Board Sensor Cable Replacement

    Probably a duh question here but I'm going to replace the board sensor cable on one of my machines to see if that corrects an intermittent board sensor failure problem, and possibly the fcc cable as...
  21. Replies
    5
    Views
    372

    THANKS! I did glance at the calibrating...

    THANKS! I did glance at the calibrating instructions but I must have missed the depth option, I just had to adjust the board length so I'll give that a try. I appreciate the link.
  22. Replies
    5
    Views
    372

    I should have been more clear I was using the...

    I should have been more clear I was using the normal 1/16 and 1/8 bits that come with the collar on them. I do have some of the clear stop collars so I can use them. Giving it more thought the bit...
  23. Replies
    5
    Views
    372

    Wood may be too thin message.

    I'm kind of an intermediate level user but learning all the time, I keep getting a message wood may be too thin, but it's 3/4 and the mpc says 3/4, so there isn't a problem there. When changing bits...
  24. Replies
    4
    Views
    604

    Quick Change Cutting Bit

    I have a new unused QC cutting bit available, just pay the shipping!
  25. Replies
    3
    Views
    450

    After trying almost everything it was Lateral...

    After trying almost everything it was Lateral Stabilizer just got it installed today and gonna try to carve something tomorrow!
Results 1 to 25 of 56
Page 1 of 3 1 2 3