Search:

Type: Posts; User: lynnfrwd; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds.

  1. When the machine expects a certain bit based on...

    When the machine expects a certain bit based on the software assignment, and it hits the slap plate or board either sooner or later than it should, it will give you the z-axis warning.
  2. Is your project set up with the long carving bit?...

    Is your project set up with the long carving bit? Edit > Boards Settings > Pattern Bit > 1/8" Long Carving Bit. (Reminder to others: the 1/16" long carving bit cannot be used on the rotary jig.)
  3. This probably means the bit is touching the plate...

    This probably means the bit is touching the plate sooner or later than it expects to touch it. What bit do you have assigned and what bit are you using?
  4. Replies
    18
    Views
    2,483

    RNichols - the 1/16" long carving bit SHOULD NOT...

    RNichols - the 1/16" long carving bit SHOULD NOT be used on the rotary jig. You need to use the 1/8" long carving bit.
  5. Don't know if you plan on carving that way or...

    Don't know if you plan on carving that way or just testing, but that would be an awful lot of unnecessary carving. Use your connected line tool to trace around the the part, just a little bigger....
  6. Thread: Meshlab

    by lynnfrwd
    Replies
    3
    Views
    3,469

    88243882448824588246Adding screenshots for...

    88243882448824588246Adding screenshots for meshlab instructions from Michael Tyler's original post.
  7. Replies
    1
    Views
    237

    What size is the file? Have you tried the...

    What size is the file? Have you tried the instructions from the Meshlab post?
  8. Thread: runtime error

    by lynnfrwd
    Replies
    7
    Views
    1,451

    Michael T's snapshots

    88240882418824288239Adding Michael Tyler's Snapshots for Meshlab Settings. They posted in reverse order.
  9. Replies
    9
    Views
    607

    I assume you are asking if we have them in stock....

    I assume you are asking if we have them in stock. We do.
  10. Replies
    9
    Views
    607

    Different pins are used when uploading a project...

    Different pins are used when uploading a project and accessing in machine. Look inside for bent pin.
  11. Replies
    2
    Views
    1,231

    Ken Johnson - aka DocWheeler

    A member of our CarveWright family, since early 2007, it is with deep regret to inform you that we have lost another Senior member and huge contributor to our community. Thank you, DocWheeler.
    ...
  12. Evidently, Ken passed away last Friday. Thank...

    Evidently, Ken passed away last Friday.
    Thank you, sir, for all those that you helped.
    Prayers for his family.
  13. Things to remember when doing a project like this...

    Things to remember when doing a project like this (assuming this is what you are looking for):

    1. place photo
    2. place circle
    3. give circle a carve region (depth same as photo)
    4. select...
  14. Like this? 88151

    Like this?

    88151
  15. What kind of border?

    What kind of border?
  16. Replies
    3,314
    Views
    1,876,530

    Sticky: You DO NOT want to do that. First of all, not...

    You DO NOT want to do that. First of all, not all of those patterns are of good quality. Second and most important, downloading and installing that many patterns will terribly slow down the...
  17. Good to see you still signing in! Hope you get...

    Good to see you still signing in!

    Hope you get your plaques done.

    Connie
  18. Please keep Ken Johnson (Doc Wheeler) in your prayers

    Ken is one of our pioneers in the CarveWright Family joining February 2007.

    Please keep him and his family in your prayers as he nears the end of his time here on earth.

    Doc we love you and...
  19. Replies
    7
    Views
    5,721

    To ship to Canada would have been $45, but we...

    To ship to Canada would have been $45, but we instead shipped two sets under warranty to your address in Montana at no charge.


    The rest of the story...
    ~Paul Harvey
  20. Replies
    5
    Views
    2,959

    Still waiting.

    Still waiting.
  21. Thread: Lithograph

    by lynnfrwd
    Replies
    6
    Views
    543

    If you have Designer 3, you can preview it.

    If you have Designer 3, you can preview it.
  22. Thread: Lithograph

    by lynnfrwd
    Replies
    6
    Views
    543

    It is a Lithophane or Lithopane. Lithograph is...

    It is a Lithophane or Lithopane. Lithograph is something different.

    To answer your question, I don't think it matters which side.

    If not enough light is coming through, make the overall...
  23. Thread: Belts Tearing

    by lynnfrwd
    Replies
    4
    Views
    1,178

    You said tore, so is it on the glued line...

    You said tore, so is it on the glued line separating? Did the corner of a board snag it? May just be old glue or head pressure is too high (with sandpaper belts should be 70-80).

    When you put your...
  24. Replies
    5
    Views
    758

    Anytime a file is named, you should AVOID using...

    Anytime a file is named, you should AVOID using (.) a period. Computer programs see the period as the end of the file name and the first three letters after the period indicate which type of program...
  25. Replies
    12
    Views
    902

    7" difference. (7 inch rule.) Say NO to stay...

    7" difference. (7 inch rule.) Say NO to stay under rollers, if you have added the 7" to the length of your actual board or are using a jig. READ CHAPTER TWO:...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4