I have not tried to scan anything for several years but recently tried to scan a cross that my wife has. The problem I'm having is that the scan tip touches the sled that I have the cross fastened...
Type: Posts; User: coop2739; Keyword(s):
I have not tried to scan anything for several years but recently tried to scan a cross that my wife has. The problem I'm having is that the scan tip touches the sled that I have the cross fastened...
Thanks, all who responded. JoeS Has agreed to send me one. Thanks again.
Coop2739
The end where the flexshaft fits into the motor broke into many pieces. Anyone have an old motor that doesn't work? or does anyone have a used spare motor that they would sell to me?
coop2739
Found the problem. While doing all the changes I had left a wire over the top of the "Y" motor cooling fins which stopped the "Z" truck about 1/8" short of the home position. This left the board...
Bergerud,
Yes, when it starts to measure, it just stops about 2-1/2" in from keypad side. It reads 148-150 across the board and zero when off the board.
Coop2739
I have replaced the FSC cable, the board sensor and used different boards. It still reads 150 and stops at about 2-1/2" from the keypad side. The readout says "clear board sensor". What can I do...
The reading are consistant from side to side. The boards I have tried are flat, good clear pine, no voids and square edged.
Coop2739
I have a clear board sensor problem also. When I try to run a program (any program on my card), the head homes OK, I then press 2, the head moves about 2-1/2" to the right and stops, "Clear Board...
I am trying to create a finger labyrinth. I want to end up with a groove 3/4" wide by about .470 deep. I am trying to use a 1/2" ball nose to rough out the groove using (2) cutpaths, each offset...
Really like the chest with the grapes.
E L Cooper
Terrific job Terry
I'm having trouble adjusting the calibration of the "X" axis on my machine. I just replaced the sandpaper belts with the rubber belts. I have the old style brass roller and did change the "o-ring"...
Jon,
Thank you very much. I hope to use it very soon.
Jon,
I for one would be very interested in your Radial Vector Generator tool for generating gear profiles. If you would post it here I would very much appreciate it. Thank you in advance.
Steve,
Could you e-mail me the Cribbage Board? my son likes all kinds of Cribbage Boards and I would love to make this one for him.
E-Mail elcooper1@yahoo.com Eldon Cooper (coop2739) Thank...
Springfield - 45506
I have strips of tape across the board. The machine doesn't get to the point where it moves in "x" direction. Just stops 2-1/2" in as it is suppose to measure the width of the board. I checked the...
I know this has been brought up many times. I just started getting this message. Trying to run a project, the head goes to the left and stops at keyboard end, stay under rollers?, No, (I am using a...
Thanks Al I will take a look at the gear box. The bearings are probably bad as I have many hours of carve time on this machine.
I am trying to carve a rectangular pocket .375 deep X 2.500 X 4.250 withr the 4 corners having a .500 radius. I have carved this same project hundreds of times but now I get 45-50% through the carve...
Thank you all for the information about the Lion Head Tap Handle it looks exactly like what I was looking for. I sent a PM to Router-Jim to see if I could possibly get the pattern. Thanks again.
Looking for a double sided carve of an English Royal Lion that can be used as the top of a bottle stopper. Anyone have or know of such a pattern? Thanks in advance.:rolleyes:
Richard,
If you would send me a copy also.
elcooper1@yahoo.com
I would be interested in 2.:)
Count me in also Ron.:)