Search:

Type: Posts; User: sunmiztres; Keyword(s):

Page 1 of 10 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    28
    Views
    30,488

    I did this and it worked when I first opened...

    I did this and it worked when I first opened designer but and after I closed designer and came back to it the error came back. I will do what Steve said and hope it stays.
  2. Replies
    28
    Views
    30,488

    no, not yet was hoping someone from there that...

    no, not yet was hoping someone from there that works these forums could chime in. I know they monitor the forums.
  3. Replies
    28
    Views
    30,488

    I am now having this same problem. Made sure I...

    I am now having this same problem. Made sure I have the newest version and it still happens. I am not able to use the text button without this error. Thought it was my computer, restarted and still...
  4. Thank you for the info.

    Thank you for the info.
  5. New computer! How to unregister old computer?

    I have a new computer and have already licensed 2 computers so I need to unregister the old one before I can register the new one since only 2 licenses are allowed at one time. How do I do this short...
  6. Replies
    1
    Views
    12,676

    Changing out the Z belt pulley

    I noticed the Z pulley on the bottom of the Z belt has no teeth left. I have an extra pulley from a cannibalized machine but I am hoping I do not have to remove the entire spindle to replace the...
  7. Replies
    10
    Views
    26,886

    That is BEAUTIFUL!!!!

    That is BEAUTIFUL!!!!
  8. Replies
    17
    Views
    2,847

    I'll double check the bearings and see. Thanks...

    I'll double check the bearings and see. Thanks for helping me out bergerud.
  9. Replies
    17
    Views
    2,847

    I have cleaned the bits and I don't feel any...

    I have cleaned the bits and I don't feel any stickiness or see any white on the bits. As far as chips, it worked well for 2 carves and everytime after a carve I clean the machine. I don't have this...
  10. Replies
    17
    Views
    2,847

    I am having the same problem using Candlestone. I...

    I am having the same problem using Candlestone. I think this product is very hard and very rough on the bits. I did 2 lithos no problem but after 2 it dulls the bit that I begin to get the y axis...
  11. Replies
    14
    Views
    2,985

    I personally thought it was the machine before...

    I personally thought it was the machine before the software that is why I cleaned it thoroughly. I did take off the y encoder and checked it, blew it out, made sure the disk was not bad. The y belt...
  12. Replies
    14
    Views
    2,985

    I went ahead and tried a different MPC and it...

    I went ahead and tried a different MPC and it began to carve correctly but then after 3 passes the entire pattern shifted to the left by 1". The bottom started 1" higher which made the top of the...
  13. Replies
    14
    Views
    2,985

    If you look at the picture the entire carving...

    If you look at the picture the entire carving area moved up about an inch. It wasn't just where the carving of the cropped picture was. It's like the machine thought the edge of the carving was 1...
  14. Replies
    14
    Views
    2,985

    With the pattern of the people, I always remove...

    With the pattern of the people, I always remove the background and like to have the people higher than the board so I butt the people pattern all the way to the insides of the recessed area so you...
  15. Replies
    14
    Views
    2,985

    Thanks for looking at the post. I clipped the...

    Thanks for looking at the post. I clipped the carving so the carving would be within the frame. Why would it move the entire carving right 1 1/2". I never had this happen before and made the MPC the...
  16. Replies
    14
    Views
    2,985

    Carving moving to the right 1 1/2"

    I am having a problem that I can't figure out. I have tried 3 times. When carving it starts out fine but at about 10% through the carving the entire project moves to the right 1 1/2". I have cleaned...
  17. Replies
    12
    Views
    5,824

    Do you buy your roll of LED lights online? If so...

    Do you buy your roll of LED lights online? If so can you give the link? Thanks Rcdages
  18. Cute project Micheal. You did a wonderful job! I...

    Cute project Micheal. You did a wonderful job! I can see using the box for many things.
  19. Replies
    6
    Views
    2,990

    Thank you all for the kind words :)

    Thank you all for the kind words :)
  20. Replies
    6
    Views
    2,990

    My latest Lithos

    The first one Was for a friend's family who recently lost their son in a motorcycle accident. The 2nd one is for my Best Friend. A litho of her father and her daughter.
  21. Replies
    12
    Views
    5,824

    Thank You!!!! :)

    Thank You!!!! :)
  22. Replies
    12
    Views
    5,824

    Beautiful job. Do you use LED rope in the box? If...

    Beautiful job. Do you use LED rope in the box? If not what do you use for the light? If you don't mind me asking, what do you charge for this, and what is the size of the picture? Again Great job!!!
  23. Replies
    284
    Views
    165,297

    I 2nd that. I just love the UC.

    I 2nd that. I just love the UC.
  24. Replies
    14
    Views
    31,172

    Beautiful job. Thank you for sharing.

    Beautiful job. Thank you for sharing.
  25. Replies
    9
    Views
    2,694

    That is a great project. You did a TERRIFIC JOB!!!

    That is a great project. You did a TERRIFIC JOB!!!
Results 1 to 25 of 246
Page 1 of 10 1 2 3 4