Search:

Type: Posts; User: AskBud; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    5
    Views
    1,557

    90 degree bit burning

    It could be your font selection or the application of the BOLD option. We need to see your MPC in order to know for sure.
    AskBud
  2. Replies
    12
    Views
    1,706

    Touch Plate

    Turn the machine off and move the Truck by hand and see if you can accomplish the task with no extreme pressure. There could be several reasons for the contact not to be made, or the plate to move...
  3. Replies
    6
    Views
    776

    Owls in Pattern Depot

    There are lots of owls in the Pattern Depot. Start with animal and narrow your search to Owls.
    AskBud
  4. Replies
    270
    Views
    74,767

    Sticky: ...............

    ...............
  5. Replies
    39
    Views
    4,944

    Pattern Editing

    It depends upon how and where you obtain your original. You may not edit another persons offered pattern.

    If you there is a box around the offered pattern you may need to look for one without a...
  6. Replies
    39
    Views
    4,944

    You might start in the Pattern depot, on this...

    You might start in the Pattern depot, on this page.
    AskBud
    http://store.carvewright.com/search.php?mode=search&page=2
  7. Thread: 45 cut on end

    by AskBud
    Replies
    7
    Views
    984

    No video, but I'll send you a private message. ...

    No video, but I'll send you a private message.
    It should be a simple MPC, but will depend in the thickenss of the stock.
    This is probably the reason I have avoided publishing anything.
    AskBud
  8. Thread: 45 cut on end

    by AskBud
    Replies
    7
    Views
    984

    45 degree line/edge

    If I understand your need, you want to "bevel" the edge of your board.
    If this is what you want, you would simply assign a vector line to that edge and assign your degree bit to the depth you need....
  9. Replies
    7
    Views
    1,349

    Here it a link to the item. It may not be a true...

    Here it a link to the item.
    It may not be a true 46 degree, but you can see it's on an angle.
    AskBud
    http://www.woodcraft.com/product/2000899/7414/4-universal-fitting.aspx
  10. Replies
    7
    Views
    1,349

    wood craft store

    when I designed this my top loaded Vacuum Head, which may be what you now have, I got my 4" 45 degree fitting at the Wood Craft Store.
    AskBud
  11. Thread: delete cut path

    by AskBud
    Replies
    1
    Views
    2,288

    Highlight the unwanted cut-path, press...

    Highlight the unwanted cut-path, press "Delete",save the altered design, and load that design to the Memory card.
    AskBud
  12. Layering

    One of the first Tips & Tricks is on Layering.
    AskBud
    http://www.carvebuddy.com/PDFs/CW_TipsandTricks_Newsletters/CarveWrightTips&Tricks_Oct07.pdf
  13. Replies
    16
    Views
    3,038

    My first question is, "Di you carve all the...

    My first question is, "Di you carve all the Corian on the Optimal setting, so the the bit takes smaller cuts with each Pass"? If not, the bit is bulling through the stock which will dull the bit...
  14. Replies
    16
    Views
    3,340

    Once you have your 1st set of stop collarr you...

    Once you have your 1st set of stop collarr you should not have to get packets frrom LHR! You simply buy 1/2 or 1/4" tubing from the local hardware store, use a razor knife, and cut your own!
    AskBud
  15. Replies
    2
    Views
    583

    Bit confirmation

    Hi Steve,
    In the beginning, the machine will ask for each bit you have assigned. The last bit is usually the first bit to be used in the carving proceed. This is to register the original bit...
  16. Replies
    2
    Views
    929

    Lesson on Rotate

    This link contains 3 AVI lessons on the subject od "Rotate". Thy should help you understand the concepts.
    AskBud
    http://www2.wcoil.com/~nharbison/cw-askbud%20downloads.htm
  17. Thread: cut motor

    by AskBud
    Replies
    39
    Views
    5,378

    Cut moter warning during Centerline

    This error is usually nothing to worry about. It happens mostly on the old Quick Change Chuck, The machine is monitoring the spin speed of the cut motor. Sometimes the pressure Resistance of the...
  18. Replies
    25
    Views
    2,652

    I just copied the one you used for your cut-out,...

    I just copied the one you used for your cut-out, pasted it, and removed the cut-out on that one, reduced it for the inside area, then applied the carve area. No rocket science involved!
    AskBud
  19. Replies
    1
    Views
    378

    It sounds as if your cutting bit is mounted too...

    It sounds as if your cutting bit is mounted too long in the QC adapter, thus it poked the hole in the Brass sensor side. Have you checked the bit section, is the manual for the proper position in the...
  20. Thread: board sensor

    by AskBud
    Replies
    6
    Views
    686

    Try a different board and alter your light...

    Try a different board and alter your light source/direction. See what results you get.
    AskBud
  21. Replies
    25
    Views
    2,652

    Revisions

    I did lots of revisions!
    Applied a small draft to the vines, text was floating at .125 9Changed the depth to .250 and lowered the height to 50, removed the line carve area and just replaced it with...
  22. Replies
    25
    Views
    2,652

    Profile

    If you update your profile, similar to each of our righe hand corners (of each post) folks would have a rough idea as to where you are.
    There is also, an entire forum section for which to add your...
  23. Where does the bit touch as it prepares to carve?...

    Where does the bit touch as it prepares to carve? Does it touch on the very top of the board, as it does it'e checking, is there a lower surface where the bit is doing part of the 2nd series of...
  24. Replies
    25
    Views
    2,652

    Project Designer Link

    http://www.carvewright.com/support-page/getting-started/tutorials/software-tutorials/project-designer/
    AskBud
  25. Thread: cut motor

    by AskBud
    Replies
    39
    Views
    5,378

    Call LHR, on Monday. It may be a wirine problem....

    Call LHR, on Monday. It may be a wirine problem.
    AskBud
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4