Great Price. I will post it on the Facebook page for you.
Type: Posts; User: Digitalwoodshop; Keyword(s):
Great Price. I will post it on the Facebook page for you.
So no Sand Paper Belts.... CX.
Another option I found once.... The 4 smooth rails the whole head rides up and down on with the hand crank. I had tracking problems and found the screws in the...
Do you have Sand Paper Belts? They roll under on the keypad side. Very hard to see. It will cause Tracking Errors as the folded over belt raises the board off the tracking roller AND drive the...
The Pitch of the 18 pin FFC Flat Flex Cable is finer or closer together and thinner than the 14 pin.
If you put a 14 pin with it's wider pitch or thickness into a 18 pin socket the wider 14 pin...
Good Job !!!!
You will have to delete the back side in Designer then run again.
There is a Facebook group too for sometimes quicker answers.
Don't give up, you will master this... It will be fun.
Look at...
Lets address the two issues.
First is the tracking roller issue. Maple is very hard and very smooth. We recommend a strip of masking tape on the bottom of the board so the brass roller has...
Sorry to hear about your 18 pin cable. Due to it's thinness it would let conductors snap inside the plastic leading to many problems from the bit driving into the board and jamming, Air Carves,...
When you inspect your machine always be on the lookout for FFC Cables that have any sharp bends in the moving part. It makes the bend or kink bend in a small area leading to failure. Like a piece of...
Welcome. Also join the CarveWright Facebook Page too for quick help as you work through this first project. And get to know the machine.
Good Luck,
AL
Interesting problem..... Also you could spell out the month and a number for the date.
Rick H posted above that if you buy a new controller from LHR that they will program in your serial number. Is that correct?
If so, then it must be done through that DB-25 port. ...
Rather than buy a new controller... Another option is to send your controller and card to LHR to test... It costs.... But I don't think it is the Controller... I think it is a card issue.
I...
If I was doing this I would go with a similar single board sled like I use to cut out plastic tags. Except I would add side rails as your litho will remove material in depth and the side rails will...
Wow, So sad for you... Tragic Loss...
Welcome, This is a great place to search and learn. Be sure to join the two Facebook Pages.
I will post this question on the Facebook page. I don't remember the answer.... You have to enter the board thickness even though it is on the sled.
I will post this on the CrveWright Facebook page.
I am all talk and no action.... Did not build the Vacuum sled yet. Found 1/4 inch double stick tape made it easier, I was cutting 3/4 inch in strips so it is easier....
I still have not opened...
Here I show a Circuit Board Bit and a Roto Zip 1/4 to 1/8 inch adapter. Don't use the Roto Zip bits in the CW as they are able to BEND as they are used for Drywall and thin board. The holder works...
LHR gave me a Tip years ago that I use all the time to cut sheet Fiber Plastic. You set up your Vector lines. I do not use tabs as I use 1/4 inch strips of double sided tape to hold the cut tag. I...
Also could have Centering the object turned on.
Much more activity on the Facebook Page. You might get a quicker answer. There is a pattern section here. But I have not looked at it in Years.... Just watch out for the guy on eBay selling pattern...
Floyd will chime in shortly but I believe you need to run the STL through a program to make it smaller first then use it in Designer.
And you would likely get a quicker reply on the Facebook page....
That is almost $3K. Post your location, it might help.
I just took delivery of my 12th machine yesterday. $300.00 and $96.00 shipping. It is perfect but has a QC and a broken sand paper belt.
...