Search:

Type: Posts; User: DickB; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    22
    Views
    11,305

    https://www.ebay.com/itm/225127411568?hash=item346...

    https://www.ebay.com/itm/225127411568?hash=item346aa3af70%3Ag%3AA0cAAOSwuPdjAQi2&amdata=enc%3AAQAHAAAAoDs%2F1NLZ9%2F1Bwz8Pha1pLH1aeuCxEtlaOKoJCCVyw3%2FdeIqAE4KqwhQBc4ePiowPSX5W9mBw9rhMYXK3AQwFui%2F5Mi...
  2. Thread: Z-Axis Off?

    by DickB
    Replies
    5
    Views
    1,095

    Are you using a longer board and staying under...

    Are you using a longer board and staying under the rollers?
  3. Replies
    26
    Views
    6,717

    You need to check the compression roller switches...

    You need to check the compression roller switches as I described. It's simple and easy to do. The board sensor is not used until the roller drops. If the switch is dirty or stuck, the machine will...
  4. Replies
    26
    Views
    6,717

    Select Options (0) - Sensor Check (7) press Down...

    Select Options (0) - Sensor Check (7) press Down Arrow to display roller status. Crank down on your board. Front and Back Rollers should both read Compressed.
  5. Thread: 18 pin cable

    by DickB
    Replies
    19
    Views
    17,757

    I have not found an exact replacement in stock -...

    I have not found an exact replacement in stock - most are much smaller in length. I have a few suggestions.

    Samtec offers a 20-pin cable in the length that you need. I would try trimming one with...
  6. Thread: 18 pin cable

    by DickB
    Replies
    19
    Views
    17,757

    What I am asking is the cable a "Type A" or "Type...

    What I am asking is the cable a "Type A" or "Type B" per the attached photo.

    88660

    We also need to know the pitch of the contacts. If the cable is 3/4" wide, with 18 contacts the pitch should...
  7. Thread: 18 pin cable

    by DickB
    Replies
    19
    Views
    17,757

    Are the contacts on the same side of the cable,...

    Are the contacts on the same side of the cable, or opposite sides?
  8. Thread: 18 pin cable

    by DickB
    Replies
    19
    Views
    17,757

    A cable may be available through electronics...

    A cable may be available through electronics suppliers. Please measure the exact length and width of the cable, and if possible the spacing between conductors (will likely be in metric). Also a...
  9. FYI. I have not used one myself. 88659

    FYI. I have not used one myself.

    88659
  10. Replies
    14
    Views
    8,023

    Stimulus check? ;)

    Stimulus check? ;)
  11. Replies
    14
    Views
    8,023

    It can reduce carve time, and yes the X and Y...

    It can reduce carve time, and yes the X and Y work together with Centerline.

    The attached examples are on a 12" x 6" board. Centerline time is 3:34 and Raster 6:31.

    88650 88651


    If...
  12. Replies
    14
    Views
    8,023

    I would suggest Centerline and Conforming Vectors...

    I would suggest Centerline and Conforming Vectors for signs as suggested by lynnfrwd. I would hold off on purchasing Pro until you find that you need it, unless budget is not an issue. That said,...
  13. Replies
    9
    Views
    2,463

    After pressing 7 (Measure), press 1 to select...

    After pressing 7 (Measure), press 1 to select Length (nothing will happen until you select Length or Width). If the board moves, the controller is probably OK and it is either a bad display or a bad...
  14. Replies
    9
    Views
    2,463

    If the controller were bad I would think the...

    If the controller were bad I would think the machine would not even go through the homing process. I would pretend everything was OK and try an operation such as Measure to see if it works. I can...
  15. Replies
    13
    Views
    6,337

    It seems to be an issue with Designer Pro. It...

    It seems to be an issue with Designer Pro. It works for me in Designer Basic, but not Pro - I get the same result as you no matter the font.

    As a workaround, you could break the date into 5...
  16. Replies
    13
    Views
    6,337

    I don't have a "bullet" on my keyboard. How are...

    I don't have a "bullet" on my keyboard. How are you entering it?
  17. Replies
    14
    Views
    8,023

    Yes, please elaborate on what you would like to...

    Yes, please elaborate on what you would like to do in your projects.
  18. Replies
    4
    Views
    5,979

    You can use raster and the Invert tool. Best...

    You can use raster and the Invert tool. Best with no feather and shallow depth.
  19. Replies
    5
    Views
    8,564

    Use the Flip to other side of the model tool, it...

    Use the Flip to other side of the model tool, it will change from pink to brown and you can proceed.
  20. Replies
    5
    Views
    8,564

    Can you post the image that you imported?

    Can you post the image that you imported?
  21. Replies
    3
    Views
    4,678

    Run a board sensor test:...

    Run a board sensor test: http://support.carvewright.com/checking-and-cleaning-the-boardsensor/

    Post results.
  22. Replies
    5
    Views
    19,575

    This is the best technique to easily "carve" a...

    This is the best technique to easily "carve" a photo in wood. I use quotation marks because you're not really converting a photo to 3D, but creating slightly higher (lighter) and deeper (lower)...
  23. Replies
    7
    Views
    8,238

    ER11. Many collet sizes available. I have one...

    ER11. Many collet sizes available. I have one similar to this for my CarveTight spindle: ...
  24. Replies
    12
    Views
    13,242

    I would not go that deep - .125" would be plenty.

    I would not go that deep - .125" would be plenty.
  25. Replies
    12
    Views
    13,242

    Please post the original image (or a link) and...

    Please post the original image (or a link) and your mpc.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4