Search:

Type: Posts; User: swaggerstick; Keyword(s):

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. I have done this successfully by going back to...

    I have done this successfully by going back to the software and deleting all but the uncarved, rename it and save. Load new name in card. Make sure that you position board so that the measuring of...
  2. Replies
    5
    Views
    2,382

    Thank You for your help.

    Thank You for your help.
  3. Replies
    5
    Views
    2,382

    Cutouts

    HELP !!! I get an error message when trying to upload to memory card. "Vector loop not closed properly" This is not an important project. Just trying to learn the tips and tricks.
  4. Replies
    15
    Views
    1,532

    If none of the above works, You might try putting...

    If none of the above works, You might try putting it in an oven at about 100 degrees and bake the moisture out of it for about 4 hours. I have seen it work with a 3 phase pump motor before any power...
  5. Replies
    5
    Views
    1,511

    Have you done a "roller is compressed" in user...

    Have you done a "roller is compressed" in user options. There is a switch apparently that tells when the roller is compressed. I am speculating.
  6. Replies
    10
    Views
    1,475

    Beautiful job. What is your technique for...

    Beautiful job. What is your technique for painting the letters ?

    Thanks for sharing
  7. Replies
    21
    Views
    2,041

    This is probably a dumb answer but anything is...

    This is probably a dumb answer but anything is worth trying. Could it be like a lot of other electronic things. Shut it off, remove the card, UNPLUG IT FROM THE POWER SOURCE, leave unplugged for 5...
  8. Replies
    21
    Views
    2,792

    Chevrolet is part of GM. I think he meant Ford,...

    Chevrolet is part of GM. I think he meant Ford, Gm, and Chrysler as they were once know as the big 3. Not sure that you can classify them that way now. It is an old term that has carried over. They...
  9. Replies
    7
    Views
    1,598

    Thanks..............I thought I had it pretty...

    Thanks..............I thought I had it pretty well clean. I have only had this about a month or so. I have very few of my own patterns. Most are carvewright patterns
  10. Replies
    7
    Views
    1,598

    I have both of those Programs. The 2 that I am...

    I have both of those Programs. The 2 that I am trying to read the tutorial and then go through the same steps on my software are the address sign and the white maple leaf. I never see the white maple...
  11. Replies
    7
    Views
    1,598

    The ones I have tried to use are here. ...

    The ones I have tried to use are here.

    http://www.carvewright.com/support-page/getting-started/tutorials/software-tutorials/centerline/
  12. Replies
    7
    Views
    1,598

    Centerline Tutorial

    I have tried to use the one on carvewrights home page but I have no luck. I have 2.05 and it don't compute with what they tell me to do. Is it not up to ate or is it me? Thanks
  13. Replies
    6
    Views
    692

    Food for thought. Won't a data recovery service...

    Food for thought. Won't a data recovery service be able to retrieve that data?
  14. Replies
    31
    Views
    5,476

    Does this help Ron?

    Does this help Ron?
  15. Replies
    4
    Views
    575

    I assume that you have seen this? ...

    I assume that you have seen this?

    http://www.carvewright.com/support-page/getting-started/tutorials/accessory-tutorials/carvetight-video/
  16. Thread: Confused

    by swaggerstick
    Replies
    14
    Views
    2,454

    Feedback for you guys. I pulled up the pattern...

    Feedback for you guys. I pulled up the pattern again and deleted all but the goal post. Checkmarked the conform box, selected the 60 degree bit, renamed the project to "no carve". Uploaded it to the...
  17. Thread: Confused

    by swaggerstick
    Replies
    14
    Views
    2,454

    I am not sure. Since in the beginning when it ask...

    I am not sure. Since in the beginning when it ask for the v-bit, I discounted in my mind that it would ask me for it again. The display was dark when I got to it and since the cut motor had quit, I...
  18. Thread: Confused

    by swaggerstick
    Replies
    14
    Views
    2,454

    Was that where I messed up? fwharris Thanks

    Was that where I messed up? fwharris Thanks
  19. Thread: Confused

    by swaggerstick
    Replies
    14
    Views
    2,454

    You are right about the wood not being.75 thick...

    You are right about the wood not being.75 thick but I had changed that in the pattern that I uploaded. It measured .55 but I allowed for that. Does the bit have to be the same length as the carve...
  20. Thread: Confused

    by swaggerstick
    Replies
    14
    Views
    2,454

    Confused

    This pattern had a goal post in it that did not carve. I am guessing that either I didn't set it up right or I don't know how to allow for the bit. The machine ask me for a 60 degree bit, I put it in...
  21. Kudos to Dick B for a great job of...

    Kudos to Dick B for a great job of troubleshooting. I am sure he solved a lot of problems for Carvers and Carvewright as well. Great job Dick.
  22. Replies
    15
    Views
    2,219

    77 hours well spent. Where did you get the...

    77 hours well spent. Where did you get the patterns? You are a true woodworker. Keep up the good work.
  23. Replies
    41
    Views
    5,064

    I don't want to sound argumentative. But I was a...

    I don't want to sound argumentative. But I was a Industrial Electrician for 35 years and those numbers don't compute with me. Here is the specs that I copied from a Grizzly 2 HP dust collector. I...
  24. Replies
    41
    Views
    5,064

    I can't imagine the 6500 watt generator not...

    I can't imagine the 6500 watt generator not providing enough power. There are 746 watts in a HP. Unless you had a typo and meant 650 watt generator,.
  25. Replies
    41
    Views
    5,064

    My 2 cents. I had no dust collection in the...

    My 2 cents. I had no dust collection in the beginning. Only had 10 hours on carvewright. Motor quit in the middle of a carve. Would not restart after i sucked the dust out with a shop vac. Long story...
Results 1 to 25 of 46
Page 1 of 2 1 2