Search:

Type: Posts; User: want2b; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds; generated 3 minute(s) ago.

  1. Replies
    11
    Views
    422

    All the above! Don't know about your neighbors...

    All the above!
    Don't know about your neighbors but would be an awesome addition to my block.
    Rick H
  2. Replies
    19
    Views
    3,545

    Nice job, should be something they will treasure...

    Nice job, should be something they will treasure as a keepsake of the big event.
    Rick H
  3. Replies
    195
    Views
    17,039

    Never used beech either but as above, really like...

    Never used beech either but as above, really like it. Great carving.
    Rick H
  4. Thread: Finished Facade

    by want2b
    Replies
    20
    Views
    3,817

    Glad to hear Chris is still around. He was one of...

    Glad to hear Chris is still around. He was one of the early ones who set the tone of sharing of talents on the forum. Would be great to see him back in the carve.
    Rick H
  5. Replies
    2
    Views
    210

    Thx, knew it had to be simple, just didn't look...

    Thx, knew it had to be simple, just didn't look there.
    Rick H
  6. Replies
    2
    Views
    210

    lithopane question

    Have upgraded and have 3.106. Am trying to use the litho viewer but haven't figured out how to 'launch' it. Have tried to find a new prompt that would help but have missed it. I have verified I...
  7. Replies
    7
    Views
    682

    I am using 1.187 and the 'import to trace'...

    I am using 1.187 and the 'import to trace' doesn't ring a bell. Guess the question is what is the version you are using? You mention the basic so I'm guessing you are at 1.187 since it comes with the...
  8. Replies
    7
    Views
    682

    Not sure what you are wanting to duplicate. The...

    Not sure what you are wanting to duplicate. The probe does a good job but has limitations. I have used it to replicate unique appliques with good results but have had to do a lot of cleanup in...
  9. Replies
    7
    Views
    586

    Would you please post the hours run? Thx, Rick H

    Would you please post the hours run?
    Thx, Rick H
  10. Replies
    19
    Views
    1,291

    After seeing the final product it was obvious the...

    After seeing the final product it was obvious the layering was the way to go. Started on some Xmas gifts early, attached are 2 of 8 completed recently. One is oak background the other is sycamore....
  11. Replies
    10
    Views
    697

    Just an FYI update, got time to try a carve and a...

    Just an FYI update, got time to try a carve and a 1 1/2 hr one ran fine.
    Rick H
  12. Replies
    5
    Views
    335

    AL, You're out of my league with all the...

    AL,
    You're out of my league with all the options but one thing I found out by a fluke might help you if controlling the depth using a 'centerline' type text carve would help. I found that by...
  13. Replies
    3
    Views
    246

    Sounds like you've narrowed it down to one of the...

    Sounds like you've narrowed it down to one of the bearings frozen. I've had it happen and WD didn't help, had to bite the bullet. Reality, trying the WD shouldn't hurt, what have you got to lose....
  14. Replies
    195
    Views
    17,039

    Another beautiful project. I keep kicking myself...

    Another beautiful project. I keep kicking myself when I see these you post, just got to make some time.
    Thx for sharing, Rick H
  15. Replies
    10
    Views
    697

    Replaced the ribbon cable from the controller up...

    Replaced the ribbon cable from the controller up to the terminal board. First and hope the last time, quite a pain in the XXX. Anyway, stall error message gone. Haven't had time to do a carve to see...
  16. Replies
    10
    Views
    697

    I did try a different card, forgot to mention...

    I did try a different card, forgot to mention that earlier.
    Thx for the reply, Rick H
  17. Replies
    10
    Views
    697

    No difference in resistance, think you have hit...

    No difference in resistance, think you have hit it . Didn't think about that test, in my mind seeing the position numbers change during the check was enough. Didn't realise the processor would be...
  18. Replies
    10
    Views
    697

    Z Axis Stall 06-0313

    Started a project and the moment I selected the project the Z Axis stall appeared on the screen. The truck was in the center of the machine never moved, I did not hear any sound indicating a 'homing'...
  19. Replies
    5
    Views
    616

    As with CarverJerry, interested but need more...

    As with CarverJerry, interested but need more info, would like to have machine serial number so Carvewright can verify the machine.
    Rick H
  20. Thread: Latest projects

    by want2b
    Replies
    11
    Views
    887

    I agree, you should be very happy with the final...

    I agree, you should be very happy with the final product. Haven't had the nerve to try one myself but your project does make me want to make something that beautiful.
    Rick H
  21. Replies
    6
    Views
    466

    Just might make somebody think. Neat. Rick H

    Just might make somebody think. Neat.
    Rick H
  22. Replies
    3
    Views
    277

    I can't remember all the materials that are good...

    I can't remember all the materials that are good or bad but I know there is a problem with some melting and sticking to the bit.
    Just an FYI if you haven't checked it out. Many posts regarding...
  23. Replies
    13
    Views
    650

    Would short in the wiring to the sensor give that...

    Would short in the wiring to the sensor give that type of constant reading or go the other way to a low one?
    Rick H
  24. Replies
    7
    Views
    894

    Have to second all the previous posts. Really a...

    Have to second all the previous posts. Really a cool project, unique with a lot of thought.
    Rick H
  25. Thread: Text Question

    by want2b
    Replies
    12
    Views
    772

    I just have the basic 1.187. From the above post...

    I just have the basic 1.187. From the above post seems like the software does not recognise <CR> as a valid character when moving it to the wood. Work around seems like the quickest and easiest fix.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4