Search:

Type: Posts; User: Digitalwoodshop; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.05 seconds.

  1. Not yet... But I am looking into using a Dewalt...

    Not yet... But I am looking into using a Dewalt Brushless Router with the slap on battery eliminator 120 volt plug. I see on some CNC Pages some guy is already playing with the project and used a 15...
  2. ALSO since you needed to tighten the Y Belt... I...

    ALSO since you needed to tighten the Y Belt... I would QUICKLY order some 685ZZ Bearings and make plans for some preventive maintenance and replace the two bearings inside the Y Gearbox. Having to...
  3. Replies
    5
    Views
    146

    If you dumped a pile of sawdust on the floor then...

    If you dumped a pile of sawdust on the floor then sucked it up with your shop vac you would get that same shock.. It is the sawdust flowing through the hose that makes the static.

    And yes, in the...
  4. Replies
    3
    Views
    162

    Before you change anything if it was me I would...

    Before you change anything if it was me I would carve the very same board again. Since it did not cut deep enough.

    I would pay attention to:

    1. Be sure the bit is tight enough and not sliding...
  5. Replies
    1
    Views
    76

    Thank You Tim for helping us to understand what...

    Thank You Tim for helping us to understand what has happened... You are the BEST !!!!!

    AL
  6. Replies
    60
    Views
    1,766

    ( The Older I get... The Better I WAS ) 20 years...

    ( The Older I get... The Better I WAS ) 20 years fixing Navy Fire Control Radars and Computers. Then off to Sony in 95 making picture tubes or CRT's. Was a Shift Mechanic for 12 hours in the middle...
  7. Replies
    60
    Views
    1,766

    I deleted my Power Supply Wire Rant. Joe is...

    I deleted my Power Supply Wire Rant. Joe is taking care of it.
  8. Replies
    60
    Views
    1,766

    Here are some pictures of Really BAD X...

    Here are some pictures of Really BAD X Termination Boards.... I believe some are caused by UN GROUNDED machines that build up STATIC ELECTRICITY on the Machine FRAME and ARC OVER taking out some...
  9. Replies
    60
    Views
    1,766

    Got the note... Thank You :) I believe it is a 2...

    Got the note... Thank You :) I believe it is a 2 Watt resistor. The Brown is NORMAL.... I believe the X Termination Board is GOOD.... When they FAIL... They BURN... I will post a 2nd reply with...
  10. Replies
    2
    Views
    106

    Tapered Boards are the leading cause of broken...

    Tapered Boards are the leading cause of broken gears. Tapered in Thickness.
  11. Replies
    7
    Views
    194

    Good JOB !!!! Everyone..... For the future,...

    Good JOB !!!! Everyone.....

    For the future, since every board is a different color... Use a piece of white copy paper on the board and crank the head down and measure the Board Sensor. A 156 is...
  12. Are you a member of the Facebook page? If not......

    Are you a member of the Facebook page? If not... Lots more Activity on that page... You might find someone parting out a machine...
  13. To clarify. I have been a owner since 2007. I...

    To clarify. I have been a owner since 2007. I had some early cracked front motors but they were both used and were shipped to me with the flex installed in the cut motor. This put undue stress on...
  14. I see the broken part is in the REAR of the Cut...

    I see the broken part is in the REAR of the Cut Motor. Honesty since 2007 this is the First one I have heard of... I have had the Flex End crack on a few cut motors. All were shipped with the Flex...
  15. Replies
    10
    Views
    366

    I like the Shim Idea posted above.. That is what...

    I like the Shim Idea posted above.. That is what I would do.
  16. Replies
    60
    Views
    1,766

    What are your sled tails length. Sure looks like...

    What are your sled tails length. Sure looks like 3.5 inches.... I always do 4 inches... 3.5 inches lets the board "Tighter" on that roller "EDGE"... I like the extra 1/2 inch...

    I would try the...
  17. Replies
    5
    Views
    491

    Good Job !!!!

    Good Job !!!!
  18. Replies
    8
    Views
    444

    Sorry to just throw out the 7 inch rule of wood...

    Sorry to just throw out the 7 inch rule of wood without explaining it.... So here it goes.... The Readers Digest Version...

    So the top black rubber rollers are 7 inches apart. And the bit is...
  19. Replies
    8
    Views
    444

    Yep, the 7 inch rule of wood....

    Yep, the 7 inch rule of wood....
  20. Replies
    14
    Views
    1,522

    If you still have it crank head down on a sheet...

    If you still have it crank head down on a sheet of white paper and use sensor data to see the value. 156 perfect 100 dirty window.
  21. Replies
    3
    Views
    391

    A whole list of things can cause this.... The 2...

    A whole list of things can cause this.... The 2 lead screws have been known to strip the nut on top. Sawdust caked in the lead screw can jam the head. The 4 smooth posts could have dry grease on...
  22. Replies
    14
    Views
    1,522

    I mentioned it on the CarveWright Facebook Page....

    I mentioned it on the CarveWright Facebook Page. Might help. That is a great price.

    AL
  23. Replies
    6
    Views
    568

    And speaking of disappearing TEXT... Some fancy...

    And speaking of disappearing TEXT... Some fancy text, the far left side of some fancy first letters will be missing from the carve... In that case use a TAB 1 space then start your text.
  24. Replies
    6
    Views
    298

    You can overlay a shallow carve region like a...

    You can overlay a shallow carve region like a square or any shape on top of your text to help connect the script text or like I do to make a base for the BEAR... Then Outline and assign a cut bit for...
  25. Impressive !!!!

    Impressive !!!!
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4