Search:

Type: Posts; User: earlyrider; Keyword(s):

Page 1 of 16 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    28
    Views
    30,524

    How do I get to the McAfee rules to allow gui.exe...

    How do I get to the McAfee rules to allow gui.exe and allow fontgen.exe?
  2. Replies
    19
    Views
    8,200

    I'd like 3, Thanks. Ron

    I'd like 3,
    Thanks.
    Ron
  3. Since we're trying to survive the annual 'climate...

    Since we're trying to survive the annual 'climate change', after making the Paint Brush Clock, howabout a thermometer with extremes on either end, like a Polar bear frozen in a block of ice, and on...
  4. Replies
    0
    Views
    618

    ER 20 Spindle

    I am looking for two ER 20 spindles to refit into a couple "A" machines. If you have one or two spare or unused, please let me know.
    Ron
  5. Replies
    1
    Views
    751

    Floyd helped me out! Press 0 then 5 then 3 and...

    Floyd helped me out! Press 0 then 5 then 3 and stop 3 times. Back in project menu. Hope this might help others!
  6. Replies
    1
    Views
    751

    Accessory Menu

    Just acquired an old "A" machine that has only 10 hours on cut motor. After checking config. menu and access. menu, I can't get back to the project menu. The machine hasn't been run in about 9 years....
  7. Replies
    8
    Views
    2,537

    Ash works well by hand and machine, resists...

    Ash works well by hand and machine, resists splitting, and takes screws and nails well. It was the lumber used most by the early auto industry for building the body "skeletons" for the coach-built...
  8. Replies
    5
    Views
    2,689

    BJB, Thanks much. That will work nicely!

    BJB, Thanks much. That will work nicely!
  9. Replies
    5
    Views
    2,689

    Civil War Cannon

    Does anyone have a pattern or grayscale image of a civil war cannon? Any help will be appreciated.
    Ron
  10. Replies
    20
    Views
    4,928

    Yes, the motor will run backwards. I did that...

    Yes, the motor will run backwards. I did that years ago, and wondered why the bit cut poorly and burnt the wood. Al helped me out on that.
  11. Replies
    14
    Views
    5,247

    Consider what Groucho Marx would say, "Three on a...

    Consider what Groucho Marx would say, "Three on a (hookah, midget, match) is bad luck!"
  12. Yeah, I'll try a new bearing first, then if...

    Yeah, I'll try a new bearing first, then if necessary, try the loctite.
  13. Mine works fine, although a little noisier than...

    Mine works fine, although a little noisier than the original. The spindle slid almost too easily into the top bearing (not quite the press fit as the original). I haven't tried replacing the top...
  14. Have collets in hand now. Just need to put z...

    Have collets in hand now. Just need to put z truck in working machine. Should have something to report this next week.
  15. Replies
    5
    Views
    1,932

    Was it carved by Ho Lee Cow? (Sorry, couldn't...

    Was it carved by Ho Lee Cow? (Sorry, couldn't help it.) Astonishing detail.
  16. Replies
    4
    Views
    1,555

    Simply use a thicker board. It can be as thick as...

    Simply use a thicker board. It can be as thick as 5" (the carving will still only be as deep as you specified).
  17. Al, when I tried to buy the gear, CW wouldn't...

    Al, when I tried to buy the gear, CW wouldn't sell it to me. They wanted me to buy the entire Y motor setup. Anyone else have this problem? I don't want to spend $80 for an eight dollar problem.
  18. Replies
    16
    Views
    7,701

    You can also get 2" and 3" radial bristle discs....

    You can also get 2" and 3" radial bristle discs. These last considerably longer than the 3/4 or 1" discs.
  19. Thread: Fossils

    by earlyrider
    Replies
    12
    Views
    5,346

    For those without 2.0

    For those without 2.0
  20. Thread: Fossils

    by earlyrider
    Replies
    12
    Views
    5,346

    Fossils

    64222 Huntonia huntonensis trilobite, Devonian age, Haragan formation, Oklahoma
  21. Thread: Hand cuffs?

    by earlyrider
    Replies
    8
    Views
    4,133

    Maybe use the Wedding Rings pattern in the store?

    Maybe use the Wedding Rings pattern in the store?
  22. Replies
    15
    Views
    5,243

    Can't seem to find that color in acrylic or...

    Can't seem to find that color in acrylic or lacquer. Nor in the Exhaustive Concordance. Apocryphal?
  23. Thread: Drum Sander

    by earlyrider
    Replies
    11
    Views
    3,777

    The sanders are good for figured grain that might...

    The sanders are good for figured grain that might otherwise be chipped out with a planer.
  24. Replies
    10
    Views
    2,947

    How about doing it in layers- a foreground and a...

    How about doing it in layers- a foreground and a background, then glue them together. The foreground would be a pierced carving. The challenge would be manipulating the depth of the various elements....
  25. Replies
    10
    Views
    4,584

    We make dinosaurs too, but not in quite the same...

    We make dinosaurs too, but not in quite the same way.635286352963530 Ceratosaurus, Tanycolagreus, and Tyrannosaurus (pair)
Results 1 to 25 of 388
Page 1 of 16 1 2 3 4