Thanks.. but still nothing. Connection on the new FFC cable are secure and new Z motor connector is firm and connected well as other connections on the termination card. I notices small resistors on...
Type: Posts; User: RickC; Keyword(s):
Thanks.. but still nothing. Connection on the new FFC cable are secure and new Z motor connector is firm and connected well as other connections on the termination card. I notices small resistors on...
OK got new Power supply, New Z motor, New ribbon cable.. checked all wiring.. still getting Z Axis stall E06-0313 after selecting project and hitting start. When I do tests X & Y are fine.. Z and...
OK got new Power supply, New Z motor, New ribbon cable.. checked all wiering.. still getting Z Axis stall E06-0313 after selecting project and hitting start. When I do tests X & Y are fine.. Z and...
@leop Have you resolved this issue. I have exact problem. Machine just sits there with 0313 z error at start of any project new or old no homing no board measure, nothing... During test mode Z and...
I got it.. I flipped the cut out.. Drove me nuts..
- rickC -
Board selected is 14" x 3.5" x 1/2" but issues seems to follow any size board.
I need to create a cut path arc facing left. I have the ends beyond the board and cut path is fine except when arc is...
Yes formatted and loaded it on to card.. Thanks..
RickC
Going back to new version, 1.134 had same problem with calibration.. Works great till it does second length stroke on keypad side of 'cal sensors'. Still getting error "Cal Range Error' :(
...
Found 1.134 going to loader up.. then do calibrations. Anxious to see what happens.
RickC :)
Hi.. I suspected the sw update but wanted to be sure. I had no problems before, now I have had several issues with measurement, finding edge failures and patterns no lining up when doing 2 sided...
Hi all.. My cut path and carvings did not align with front and back. Before examining my work I decided to do a calibration test as I have done in the past to be sure things were right. I went to...
Hi floks.. thanks for info.. During my experiments to duplicate cut path on second side of work, not realizing as you explained 2nd side gets cut first, I left duplicate cut paths there overlapped....
Jerry, I copied and pasted the front design to the back.. it is duplicate of front. I did not copy and past the cutouts, the only cutout layout is on the front side.
RickC
-----------------
Thanks Jeff, that may be a problem here because it is not carving side 2 first.. I have the cut pattern on side one with my carve area, the machine carves then asks for cut bit and does the cut, it...
To maintain stability during 2 sided carving I would like to make the final cut pattern on the second side after both sides have carved. But, the cut seems to only allow to be done on the first side....
Is there a way to change the location that the machine uses to check the surface of the work. I would like to have it do its test in the center of the work or anywhere for that matter on the actual...
I believe all you have to do is bring the ends of your arc past the length of the project wood a little on both ends. This will bring up the cut options. Hope this helps.
Thank you, very informative. One more question, I assume the answer will be no but we all know about assuming.. With a wide sled when I enter a thickness less than .5 on the keypad, will I get a...
When you say can't discover depth of stock, do you mean it will not go through the finding surface routine where the bit touches the surface of the wood? I would like to know which thickness you...
I must be missing something.. How do you unattach? Once I enter a number at a node for distance to an edge lets say, the line changes from green to yellow and it can not go back to green if I need it...
A bit of code for a skilled programmer... :) It would be nice to select an option to position the light to the curor. In this way as you move the cursor the light changes position over the work....
Thanks Dave-Carve.. I will check file size and trim it up. I may have well over 600. I use Corel Draw and as you I use multi monitors.. really a must have. I rarely use more than 50 or so fonts on a...
Well the idea offered of a possible bad font file may have been but I tried the same program on different computers, another of my office computers, my wifes, and my notebook. All with different...
Yes Dave-Carve.. Seems some of us have a problem using 1.029 when entering text. Computer comes to an almost hault, can take 5 min to enter line of text a character at a time. I get around it by...
Hi all.. I noticed some postings from those using Center Line. I just received my Carvewright about 3 weeks ago and have been using the packaged version of software 1.120.
I downloaded a demo...