Thank you very much !!! I wish I knew how to make patterns like that. I hope it didn't take too much of your time ! Thanks !
Type: Posts; User: Rick P; Keyword(s):
Thank you very much !!! I wish I knew how to make patterns like that. I hope it didn't take too much of your time ! Thanks !
Who sells a pattern of an Irish Setter? Or if I get a picture, who could make a pattern??
Reply:
Warm shop...same temp for 10 years :-) Test info I saw is below... Cut Motor problem I think ??
OK...I'm going to post everything I saw because I have never had to do this before...Test...
Well, just hit a problem I have never seen before...setup steps went fine until it got to Routing Figure...then nothing...then a few clicking sounds and the 60 degree bit tried to move through the...
Thanks Perry (myshop) !!! I still have only 1.187. Are you happy with 3.0 ? Do you use both 1.187 and 3.0 ?? My heart inclines to the right :-)
Thank you Mugsowner !!!
Does anyone have a simple maple leaf pattern? (I use old Designer 1.187)87051
They built my saw ! Interesting !!
I got a CW message when downloading a project that stated ...
“ Scaling Disabled “
“This project uses features that can not be scaled. Scaling by the Carvewright Machine will be disabled.”...
I have not kept up with all the software & pattern licensing stuff very well, so I'm sure it's my fault none of my patterns are listed in my account. I have used all my patterns in projects over the...
There were no patterns listed. Not much there. ??
I have a pattern that I installed years ago. I cannot find it now, but it is still listed in my Licensed Patterns.
But, I do not know how to install the pattern again. Can someone help me?
Do you remember Lake Mile Lacs in central MN? It has been a famous walleye lake since MN became a state...but, there are issues going on now with the walleye. Local resorts, businesses and DNR are...
Thank you !
[QUOTE=fwharris;266509]Yes the MPC files Dick posted will open in 1.187 so you can do them. Just select the files, save them and open them.[/QUOTE
Thank you !!
Would I be able to make this box with my old version of Designer, 1.187, and my old Carvewright machine from 2008?? I have not been able to afford to do any updating of my machine, but it still works...
[QUOTE=DickB;266496]Here's a walleye sign: https://forum.carvewright.com/showthread.php?26432-Walleye-sign&highlight=walleye. You need a v bit for this.[/QUOTE
See my question below...please...
The sign is for my pastor...he is a bass fisherman mostly...but, he has said the walleye looking sign is fine.
DickB...If I use the 90 degree V-bit like the project calls for, will the curved body lines actually be feathered to a point just the way it looks?84699
I am looking to make a fish shaped cabin sign. I would carve a last name and the address numbers on the sign.
It needs to be about 11 inches long. Anyone done this before and willing to share the...
I think the problem was in fact mainly head pressure. There were a few things happening...a perfect storm ? :-) It got very humid here in Minnesota and I had not put out my dehumidifier yet....
The first cutout went fine...the second one was bad? Anyone know why that might happen?
My thickness total is 3/4". I am using a 1/2" carrier board with a 1/4" project board taped on top.
Could...
I ordered some cutting bits for my Rock Chuck from Ron Justice. I have not received them or heard back from Ron. Does anyone know
if Ron is still in business?
Did you seal the wood with no-wax shellac before doing the carve with the 22degree bit ??? After the carve is done you can stain the text.
The stain will wipe off the wood fairly easily. When the...
Very nice Rick Roy !! Would you sell the pattern ?? I have a young friend who is a great guitar player...he has competed on The Voice. Not sure if he plays cribbage though.