Search:

Type: Posts; User: JuicyCarp; Keyword(s):

Page 1 of 6 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    3
    Views
    1,544

    I spoke to Silverfoot last night, and my machine...

    I spoke to Silverfoot last night, and my machine will be with its new owner hopefully by the end of the week! I spoke with him on the phone for a while and informed him that this forum is going to...
  2. Replies
    4
    Views
    1,597

    Silverfoot, I am selling my machine as listed...

    Silverfoot,

    I am selling my machine as listed below. What is your budget?

    CarveWright Version C (less than 200 hours)
    Heavy Duty Traction Belts
    Project Designer Software
    Scanning...
  3. Replies
    3
    Views
    1,544

    Selling my machine...

    Hey guys,

    So I have had my fun, and a few frustrations but its time to sell the machine and move on to something new! Y and Z motor assemblies have both recently been replaced. I haven't had...
  4. Replies
    37
    Views
    9,286

    How on earth do you guys get those amazing...

    How on earth do you guys get those amazing finishes on your projects? I am guessing its not as simple as brushing on a few coats of poly?
  5. Replies
    4
    Views
    2,219

    Z truck loose

    I have been getting unwanted grooves carved throughout my carvings. with assistance from this forum i have determined the likely cause is loose screws on the z truck bearings. both of the screws on...
  6. Thread: 6 hour carve

    by JuicyCarp
    Replies
    8
    Views
    2,952

    Lynn, The screws on the Z motor bearings were...

    Lynn,

    The screws on the Z motor bearings were a bit loose. Strangely I cannot get one of them to tighten down, I am not sure why that is at the moment. However I tightened the rest down and...
  7. Thread: 6 hour carve

    by JuicyCarp
    Replies
    8
    Views
    2,952

    6 hour carve

    I just started a 6.5 hour carve, will the machine have any trouble running that long? I have never done a carve this large, so I am a bit nervous about it. I am doing the carve in pine, and have a...
  8. Replies
    5
    Views
    2,442

    Thanks for the help fellas, let me see if I can...

    Thanks for the help fellas, let me see if I can answer a few questions...

    The board was under both rollers during the whole carve. I loaned out my saw, so I just carved in the center of the...
  9. Replies
    5
    Views
    2,442

    What caused this?

    Carvewright should come with a 100% money back guarantee to turn your hair grey! I recently replaced the Z motor after the encoder disk broke. After replacing the motor I started a carve, got about...
  10. Replies
    4
    Views
    2,146

    I mentioned that to the customer, who related...

    I mentioned that to the customer, who related that he actually likes it that way! I guess since he is paying for it right? My Z motor should be in the mail today, so hopefully i can get started on...
  11. Replies
    4
    Views
    2,146

    My toughest project yet...

    I havent started carving yet because my machine is down, but Iwanted to share my next project with you guys, to see if there was any advice! Its going to be a large carve for a construction company...
  12. Replies
    1
    Views
    1,450

    Found my Z axis problem!

    Hey guys, after speaking with tech support, I beleive I have isolated the z axis error problem, and I wanted to share it. I will find out monday, but I think LHR is going to replace the motor for...
  13. Thread: Zaxis Stall

    by JuicyCarp
    Replies
    14
    Views
    4,818

    im trying to upload a video now!

    im trying to upload a video now!
  14. Thread: Zaxis Stall

    by JuicyCarp
    Replies
    14
    Views
    4,818

    I wi hopefully be able to call them today. ...

    I wi hopefully be able to call them today. Thanks guys!
  15. Thread: Zaxis Stall

    by JuicyCarp
    Replies
    14
    Views
    4,818

    Any other ideas? I love this machine but I'm on...

    Any other ideas? I love this machine but I'm on the verge of selling it!
  16. Thread: Zaxis Stall

    by JuicyCarp
    Replies
    14
    Views
    4,818

    Badbert, flashing the card fixes most of my...

    Badbert, flashing the card fixes most of my problems, but hasn't fixed this one
  17. Thread: Zaxis Stall

    by JuicyCarp
    Replies
    14
    Views
    4,818

    Thanks for the help! Fortunately (or...

    Thanks for the help! Fortunately (or unfortunately depending on how you look at it) the cable appears to be in good condition and is secured in the connector.
  18. Thread: Zaxis Stall

    by JuicyCarp
    Replies
    14
    Views
    4,818

    Zaxis Stall

    This only happened because I told a guy last night that I would have a sign carved for him for a party on Saturday morning!

    I am getting a z axis stall message, no matter what I try to do. ...
  19. Thread: Tattoo Gun

    by JuicyCarp
    Replies
    6
    Views
    3,203

    61670 Here was my attempt at a tattoo gun...

    61670

    Here was my attempt at a tattoo gun pattern, I dont know how its going to carve yet!
  20. Thread: Tattoo Gun

    by JuicyCarp
    Replies
    6
    Views
    3,203

    That looks great! I took a stab at creating one...

    That looks great! I took a stab at creating one last night as well, I will post on here when I get home tonight... you can never have too many tattoo guns! Thanks guys!
  21. Thread: Tattoo Gun

    by JuicyCarp
    Replies
    6
    Views
    3,203

    Tattoo Gun

    I know its a long shot, but does anyone have a tattoo gun pattern?
  22. Replies
    67
    Views
    24,637

    LHR should do something like this!

    LHR should do something like this!
  23. Replies
    10
    Views
    4,063

    I just thought I would post the finished product...

    I just thought I would post the finished product on here. I decided I wanted th sign to be accurate in size compared to the real thing, so this turned into my firs carve that had to be carved in...
  24. Replies
    67
    Views
    24,637

    is it cheating if someone shares the logo .mpc...

    is it cheating if someone shares the logo .mpc here for others to use?
  25. Replies
    67
    Views
    24,637

    If anyone enters this contest, I think they...

    If anyone enters this contest, I think they should post thier entry here too! I know I would love to see them!
Results 1 to 25 of 137
Page 1 of 6 1 2 3 4