Search:

Type: Posts; User: Rick P; Keyword(s):

Page 1 of 18 1 2 3 4

Search: Search took 0.00 seconds.

  1. Thread: Irish Setter

    by Rick P
    Replies
    3
    Views
    7,323

    Irish Setter - Wow !

    Thank you very much !!! I wish I knew how to make patterns like that. I hope it didn't take too much of your time ! Thanks !
  2. Thread: Irish Setter

    by Rick P
    Replies
    3
    Views
    7,323

    Irish Setter

    Who sells a pattern of an Irish Setter? Or if I get a picture, who could make a pattern??
  3. Replies
    8
    Views
    1,785

    Reply: Warm shop...same temp for 10 years :-)...

    Reply:
    Warm shop...same temp for 10 years :-) Test info I saw is below... Cut Motor problem I think ??

    OK...I'm going to post everything I saw because I have never had to do this before...Test...
  4. Replies
    8
    Views
    1,785

    Cut Motor not turning?

    Well, just hit a problem I have never seen before...setup steps went fine until it got to Routing Figure...then nothing...then a few clicking sounds and the 60 degree bit tried to move through the...
  5. Thread: Maple leaf

    by Rick P
    Replies
    9
    Views
    6,941

    Thanks Perry (myshop) !!! I still have only...

    Thanks Perry (myshop) !!! I still have only 1.187. Are you happy with 3.0 ? Do you use both 1.187 and 3.0 ?? My heart inclines to the right :-)
  6. Thread: Maple leaf

    by Rick P
    Replies
    9
    Views
    6,941

    Thank you Mugsowner !!!

    Thank you Mugsowner !!!
  7. Thread: Maple leaf

    by Rick P
    Replies
    9
    Views
    6,941

    Maple leaf

    Does anyone have a simple maple leaf pattern? (I use old Designer 1.187)87051
  8. Replies
    3
    Views
    1,215

    They built my saw ! Interesting !!

    They built my saw ! Interesting !!
  9. Thread: Scaling message

    by Rick P
    Replies
    1
    Views
    938

    Scaling message

    I got a CW message when downloading a project that stated ...


    “ Scaling Disabled “
    “This project uses features that can not be scaled. Scaling by the Carvewright Machine will be disabled.”...
  10. Replies
    4
    Views
    1,518

    I have not kept up with all the software &...

    I have not kept up with all the software & pattern licensing stuff very well, so I'm sure it's my fault none of my patterns are listed in my account. I have used all my patterns in projects over the...
  11. Replies
    4
    Views
    1,518

    There were no patterns listed. Not much there. ??

    There were no patterns listed. Not much there. ??
  12. Replies
    4
    Views
    1,518

    Installed Pattern

    I have a pattern that I installed years ago. I cannot find it now, but it is still listed in my Licensed Patterns.
    But, I do not know how to install the pattern again. Can someone help me?
  13. Replies
    10
    Views
    3,222

    Do you remember Lake Mile Lacs in central MN? It...

    Do you remember Lake Mile Lacs in central MN? It has been a famous walleye lake since MN became a state...but, there are issues going on now with the walleye. Local resorts, businesses and DNR are...
  14. Replies
    10
    Views
    3,222

    Thank you !

    Thank you !
  15. Thread: Pen box project

    by Rick P
    Replies
    13
    Views
    19,436

    [QUOTE=fwharris;266509]Yes the MPC files Dick...

    [QUOTE=fwharris;266509]Yes the MPC files Dick posted will open in 1.187 so you can do them. Just select the files, save them and open them.[/QUOTE

    Thank you !!
  16. Thread: Pen box project

    by Rick P
    Replies
    13
    Views
    19,436

    Would I be able to make this box with my old...

    Would I be able to make this box with my old version of Designer, 1.187, and my old Carvewright machine from 2008?? I have not been able to afford to do any updating of my machine, but it still works...
  17. Replies
    10
    Views
    3,222

    [QUOTE=DickB;266496]Here's a walleye sign:...

    [QUOTE=DickB;266496]Here's a walleye sign: https://forum.carvewright.com/showthread.php?26432-Walleye-sign&highlight=walleye. You need a v bit for this.[/QUOTE

    See my question below...please...
  18. Replies
    10
    Views
    3,222

    The sign is for my pastor...he is a bass...

    The sign is for my pastor...he is a bass fisherman mostly...but, he has said the walleye looking sign is fine.
  19. Replies
    10
    Views
    3,222

    DickB...If I use the 90 degree V-bit like the...

    DickB...If I use the 90 degree V-bit like the project calls for, will the curved body lines actually be feathered to a point just the way it looks?84699
  20. Replies
    10
    Views
    3,222

    Fish shaped Cabin sign

    I am looking to make a fish shaped cabin sign. I would carve a last name and the address numbers on the sign.
    It needs to be about 11 inches long. Anyone done this before and willing to share the...
  21. Replies
    9
    Views
    1,902

    I think the problem was in fact mainly head...

    I think the problem was in fact mainly head pressure. There were a few things happening...a perfect storm ? :-) It got very humid here in Minnesota and I had not put out my dehumidifier yet....
  22. Replies
    9
    Views
    1,902

    Cutout problem ??

    The first cutout went fine...the second one was bad? Anyone know why that might happen?
    My thickness total is 3/4". I am using a 1/2" carrier board with a 1/4" project board taped on top.
    Could...
  23. Replies
    1
    Views
    1,946

    Ron Justice bits

    I ordered some cutting bits for my Rock Chuck from Ron Justice. I have not received them or heard back from Ron. Does anyone know
    if Ron is still in business?
  24. Replies
    17
    Views
    3,930

    Did you seal the wood with no-wax shellac before...

    Did you seal the wood with no-wax shellac before doing the carve with the 22degree bit ??? After the carve is done you can stain the text.
    The stain will wipe off the wood fairly easily. When the...
  25. Replies
    29
    Views
    7,013

    Very nice Rick Roy !! Would you sell the pattern...

    Very nice Rick Roy !! Would you sell the pattern ?? I have a young friend who is a great guitar player...he has competed on The Voice. Not sure if he plays cribbage though.
Results 1 to 25 of 444
Page 1 of 18 1 2 3 4