Search:

Type: Posts; User: Mugsowner; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Thread: ER20 spindle

    by Mugsowner
    Replies
    13
    Views
    535

    The ER 20 spindle may be a bit hard to come by....

    The ER 20 spindle may be a bit hard to come by. Most that I have read about seem the be to big for this machine. However there was a ER11 chuck that was made for these machines. I can not find...
  2. Replies
    2
    Views
    314

    The Q C chuck has removable bits. There are two...

    The Q C chuck has removable bits. There are two set screws that hold them in. They use Loctite to keep them tight. The bits can found on EBay, but do not have the flat on them. The flat can be ground...
  3. Replies
    18
    Views
    2,425

    I would check the brushes in the motor, just to...

    I would check the brushes in the motor, just to make sure they did not cause the error message. Make sure they are long enough and slide freely, also look at the springs for damage. I had a broken...
  4. Replies
    4
    Views
    818

    Welcome, the quick change chuck is no longer...

    Welcome, the quick change chuck is no longer supported by Carvewright. However there are many places to still get parts for the chuck and bits. I have a bunch that I have purchased over the years....
  5. Replies
    247
    Views
    67,826

    Sticky: Cute bunny Oscar, and wishing everyone a happy...

    Cute bunny Oscar, and wishing everyone a happy Easter
  6. Replies
    46
    Views
    9,764

    Birds have to build nests to rear their young....

    Birds have to build nests to rear their young. Birds construct nests in areas they think are safe. Now you have a fairly smart bird there. The good news is, the young hatch and learn to fly and all...
  7. Replies
    46
    Views
    9,764

    There are a couple traps that can be built for...

    There are a couple traps that can be built for starlings. Now is the time to use them as they are nesting traps. You can pm me and we can look at this further, I do not want to steal Oscar's post.
  8. Thread: -Animals

    by Mugsowner
    Replies
    160
    Views
    62,999

    Sticky: That was my thought when I started caving hive...

    That was my thought when I started caving hive panels. Not sure about other states else, but here the hive has to have the name and phone number of the apiary on them.
  9. Thread: -Animals

    by Mugsowner
    Replies
    160
    Views
    62,999

    Sticky: Looks awesome Oscar, I think I may know an apiary...

    Looks awesome Oscar, I think I may know an apiary or two that would enjoy a few of these on their hives.
  10. Replies
    46
    Views
    9,764

    All good, I just would like folks to know what...

    All good, I just would like folks to know what these birds are capable of and the issues they create.
  11. Replies
    46
    Views
    9,764

    I never stated I had a problem with different...

    I never stated I had a problem with different bird species. I stated that sparrows and now starlings are a problem for this country as they both are evasive. As far as all your houses full of them, I...
  12. Replies
    46
    Views
    9,764

    I like the idea of using for bird houses, that...

    I like the idea of using for bird houses, that was my first idea when I saw the pattern. How ever making houses for sparrows is not a good idea as they are an evasive species in this country and are...
  13. Replies
    2
    Views
    1,318

    Wondering how many hours on motor? The switch on...

    Wondering how many hours on motor? The switch on the right side is the switch for the motor. The brushes in the motor could have issues, worn, broken spring. Pulling the motor out is a fairly easy...
  14. Thread: Angle help

    by Mugsowner
    Replies
    5
    Views
    1,322

    I do not have 3, so I can not open your mpc,...

    I do not have 3, so I can not open your mpc, however reading what you have here makes me ask, are the lines copies of each other. I notice that copied or mirrored parts of a carve tend to stay as...
  15. Replies
    37
    Views
    8,027

    The sensor saw light color then dark color and...

    The sensor saw light color then dark color and thinks it has crossed the board, giving a bad width measurement. The work around I use is masking tape in a T pattern placed where the sensor travels to...
  16. [QUOTE=Mike1;274049]This happened to me as well...

    [QUOTE=Mike1;274049]This happened to me as well but in my case the wood was too dark (pre-stained). I used a piece of natural wood as a test, and it worked fine.[/QUOTE
    When I use wood to dark for...
  17. Replies
    4
    Views
    1,226

    Are you using an offset or inset? The bit cuts...

    Are you using an offset or inset? The bit cuts the middle of the path. Depending on the bit size, the 1/8" bit would need a .062 inset on the inner and a ,062 offset on the outer. How well does the...
  18. Replies
    593
    Views
    93,001

    Sticky: Welcome, I would have to agree with Floyd on...

    Welcome, I would have to agree with Floyd on this. The tracking roller travels the bottom side of the board, on the keypad side of the machine. Make sure your board does not have any issues on the...
  19. Replies
    2
    Views
    1,470

    The quick change chuck was replaced with the...

    The quick change chuck was replaced with the Carvetite chuck system. If you need the quick change adapters, they are out there. I have a few I could part with, as I have Carvetite in all my machines.
  20. Replies
    335
    Views
    39,160

    Looks sharp Oscar

    Looks sharp Oscar
  21. Replies
    2
    Views
    612

    What would be shipping to 54130 for the 8x10's?

    What would be shipping to 54130 for the 8x10's?
  22. Replies
    10
    Views
    1,148

    Cutting is a sharp flat nose, and carving is a...

    Cutting is a sharp flat nose, and carving is a curved/angled point, right?? Right
    Did I have a wrong bit in the machine at some point and it remembers that measurement? No
    And wants to see...
  23. Replies
    6
    Views
    548

    The switch on the left side is for the cover,...

    The switch on the left side is for the cover, the switch on the right is for the motor.
  24. Replies
    3
    Views
    514

    Try going to your carve list and clicking on it...

    Try going to your carve list and clicking on it there. I have seen this before and that is ow I get around it.
  25. Replies
    3
    Views
    912

    Happy New Year

    I would like to wish all of you and your fiends and families a Happy New Year. Hope it is a good one.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4