Search:

Type: Posts; User: Digitalwoodshop; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.05 seconds.

  1. Outstanding Work :)

    Outstanding Work :)
  2. Replies
    2
    Views
    314

    The A907 is a change from the 18 pin thin wire...

    The A907 is a change from the 18 pin thin wire flat FFC Cable to a 14 pin with thicker conductors and the circuit boards for both ends. The 18 pin will work but the thin wires snapped easier and...
  3. Replies
    13
    Views
    535

    There are 2 Facebook pages for the CW. Lots of...

    There are 2 Facebook pages for the CW. Lots of discussions about the machine. Like many of us, you will learn to love the machine.
  4. Replies
    7
    Views
    383

    The machine has a feed rate setup for Wood and...

    The machine has a feed rate setup for Wood and when you attempt to cut corain it is harder and much more difficult to cut so the machine is overwhelmed.

    To give yourself the best shot I would...
  5. Replies
    4
    Views
    1,212

    My suggestion is to use a carrier board. And...

    My suggestion is to use a carrier board. And double stick tape the material down. Make your vector lines and assign the 1/4 inch round nose bit. Actually load the 1/8 inch or the bit posted above....
  6. Good one.... That may be it too....

    Good one.... That may be it too....
  7. Floyd is right. The most common failure is the Y...

    Floyd is right. The most common failure is the Y Gearbox Bearings. Then the big gear in the shaft leans toward the center of the machine and the big plastic gear rubs on the U shaped machine frame...
  8. Do you have the old bad motor?

    Do you have the old bad motor?
  9. Giving your location would help others as...

    Giving your location would help others as shipping is about $100.00.
  10. Replies
    3
    Views
    348

    Very Nice Work. :)

    Very Nice Work. :)
  11. Replies
    2
    Views
    382

    Good Job. It is all about reflective light off...

    Good Job. It is all about reflective light off the board... Dark wood reflects less... That is why the paper as a standard. Looks like my post....156...
  12. Rest in Peace Ken I just saw this today... ...

    Rest in Peace Ken

    I just saw this today...

    Then I saw a PM from Ken 3 weeks ago. He saw I had checked in and was on the Forum and sent me a note asking how I liked the 2 machines he sold me...
  13. The Compression Roller is important like Floyd...

    The Compression Roller is important like Floyd pointed out... It wakes up the board sensor... If no compression roller drop... board sensor never comes on and board drives out of the machine.... Do...
  14. The danger of not staying under the rollers then...

    The danger of not staying under the rollers then having the machine do cutting or carving within 3.5 inches of the end of the board is that while the board is only being held by one roller it can sag...
  15. Works Great.

    Works Great.
  16. Replies
    10
    Views
    1,148

    In my opinion what happened is that you installed...

    In my opinion what happened is that you installed the bits for a pre carve. When you went to install the bit a 2nd time the machine saw that the bit installed the 2nd time was a different length from...
  17. Replies
    6
    Views
    548

    Best to call LHR on this one.

    Best to call LHR on this one.
  18. I believe what I am going to do is buy two 2.2 KW...

    I believe what I am going to do is buy two 2.2 KW Water Cooled Spindles. I have the advantage that I do this as a business so it will be a tax deduction. Set one up on my small CNC and the other on...
  19. My latest idea is to skip the brushless router...

    My latest idea is to skip the brushless router and go with a Spindle... Either a Air cooled one or a Water cooled one... Replace the cut motor. Put the Spindle on the back of the machine. Sure it is...
  20. I used J-B Weld in October 2007.

    I used J-B Weld in October 2007.
  21. Replies
    5
    Views
    1,334

    That is an interesting question? I am using the...

    That is an interesting question? I am using the free software.

    Just a WAG... try a space bar before the first letter and a space bar after the last letter.

    AL
  22. On a very early "A" I saw a Magnet inside the...

    On a very early "A" I saw a Magnet inside the Spindle and a Circuit board on the back that picked up the motion. So it picked up speed at the motor and at the spindle... That spindle sensor ended...
  23. That is a very good question.... I do know...

    That is a very good question....

    I do know that to some extent the X Termination Board does control the speed of the Cut Motor... Never really understood how or why... We all know that after you...
  24. Not yet... But I am looking into using a Dewalt...

    Not yet... But I am looking into using a Dewalt Brushless Router with the slap on battery eliminator 120 volt plug. I see on some CNC Pages some guy is already playing with the project and used a 15...
  25. ALSO since you needed to tighten the Y Belt... I...

    ALSO since you needed to tighten the Y Belt... I would QUICKLY order some 685ZZ Bearings and make plans for some preventive maintenance and replace the two bearings inside the Y Gearbox. Having to...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4