This project was not made with the carvewright system. I know the person that designed this project. send me a private message and the information to the designer.
Type: Posts; User: stanv77; Keyword(s):
This project was not made with the carvewright system. I know the person that designed this project. send me a private message and the information to the designer.
Hello Connie
I can gwt to me projects although it is a pain. What I am concerned with is I do not have access to curving the text abd any thing else. I can not remember what all is in that box. ...
Hello guys,
I am having a problem with the new 2.001 software. When go to OPEN it does not go to the right open screen. The preview screen and I think there is some new items for the text. I...
Looks good Robert Bad photo and all
Hello floyd
I am still pouting. I thought he bought the machine for me(lol) I guess I am going to have to buy my own.
I have the plastic one also and had the same problem. So I went to cast aluminum for harbor freight and had no problems with them yet.
Good Morning Ton80
You might try to delete the vectors that have the undesired vector. Then pick the other side of the vector line and mirror. If you do this the extra line goes away.
I hope I...
Hello Steve
That is the way to drill the holes around the radius but I think you will have to add group of holes in the straight part of the crib board or put 2 groups around the radius....
great work sharon. I have the cowboys setting on the fence that I might have to try this on Again great work
It seems if you reduce the vibration of the chuck the heating trouble with the chuck goes away.
I made my chuck about two years ago when I was having so much trouble with QC. Since I have made mine I have had very little trouble with my machine. The flex cable does not get hot at all. I hate...
I agree with Clint that if the belt has been put on backwards it will break within seconds. I did that on my 11 inch drum sander and broke the belt and also ruined the rubber drive roller. Check...
Thanks Tom I do appreciate the help. Leave it up to me to have a problem with no time too troubleshoot. This is a little hard for my wife and I. This guy was my father-in-law and my best friend. ...
I am not sure what the problem is . I am hoping that someone can help. What is happening is when it is carving the font it fades as it gets to the bottom of the board. so end of the poem the words...
I was at the 2012 confernece and bought the new software. They showed us one that you could make a picture frame with a contour. Of course I haven'tused it for a while and I have forgotten how it...
What I do is make sled pout of cheap lumber. Make project board the actual size. I use pocket screws to attach 4 inches on both ends of the project. These boards can be saved and reused over and...
Remember the 7 inch rule. I think that the board is not staying under the rollers allowing the board to tip down. The project should be at least 7 to 8 inches longer than the project. This will...
Hello guys
Tom Watson is having trouble with the Z-truck getting to hot on one of his machines. He has changed his cut motor(new) new flex cable. We replaced the bearings in the Z-truck. We...
I have had the same problem a couple of times. If you fine a punch a little smaller than OD of the bearing you should be be able to punch it with a hammer. Be careful not to brake the housing that...
thanks for the help guys. I will post anything I find
It has only 25 hrs on the machine. I t has not been run for about 2 or 3 years
I just bought an A model machine from my nephews in-laws. I got it home was doing some testing and found that cut motor will not run and also the truck will go up or down. Does anyone have idea on...
nice job tom did the air brush work for you?
I got my bits yesterday . quicker than I expected.
thanks lawrence
I am trying to make it as thin as I can some where around 1/8 thick. As far as the sound I am getting my instructions from my friend who can play the violin very well.
For me this is strange...