Search:

Type: Posts; User: Brad Wardman; Keyword(s):

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Pattern Editor Closes Program When Clicked - HELP

    Open designer fine, then when I click launch pattern editor the whole program shuts down. Ive re-downloaded designer, shut off my virus protection and ran in compatibility mode....no luck.
    Any...
  2. Replies
    4
    Views
    1,789

    Thanks...will certainly give one a try !!

    Thanks...will certainly give one a try !!
  3. Replies
    4
    Views
    1,789

    Beautiful ROUND Cribbage Board Patterns

    There was a gentleman with a website I remember from 3-4 years back. He made beautiful cribbage boards for shows and sold several patterns on his website. Many were round with designs in the center...
  4. Replies
    13
    Views
    3,325

    I have had that happen on certain kinds of wood. ...

    I have had that happen on certain kinds of wood. First two things I would check...the bearings, both directions, on the shuttle (just grab it and make sure it doesnt wiggle around) and make sure...
  5. Replies
    8
    Views
    2,616

    What are the specs on your machine ?? Im not...

    What are the specs on your machine ?? Im not familiar with "CS" ?? or my brain isnt working properly ;-) chuck type, paper or rubber belts, etc. Any accessories & bits ?? Ive had mine for 5...
  6. Advice on SMALL or TINY Patterns - Looking for good carving patterns for Gun Grips

    Im looking for patterns that will carve really well at a small size....say 1" square and shallow. Looking for things to put on pistol grips & rifle grip caps.
    Purchased or free patterns are fine,...
  7. Replies
    22
    Views
    23,639

    I would sure like the patterns to the "Man Cave...

    I would sure like the patterns to the "Man Cave Plaque" and the "Santa" head if someone has them.
    Thanks
    Brad
    rbcarving@CenturyTel.net
  8. Replies
    2
    Views
    4,416

    Looking for LONGWORTH CHUCK Pattern !!

    Looking for a pattern for an adjustable longworth (bowl rim) chuck.
    Similar to picture.
    Thanks !!
    72040
  9. Where did I get my 1/4" shank, 1/8 square cut, 4 flute end mill ??

    Maybe an odd title, but I have been using an upcut end mill in a collet for my cutting bit (for over a year now). Well, Ive worn the couple I have out and cant remember where I got them.

    Any...
  10. Replies
    13
    Views
    5,113

    Problems solved

    PROBLEMS SOLVED !!
    Found the solutions(s) to my problems...just thought I would update both this and my other thread, in case someone else has these issues.

    Initially we had "check cut motor"...
  11. PROBLEMS SOLVED !! Found the solutions(s) to my...

    PROBLEMS SOLVED !!
    Found the solutions(s) to my problems...just thought I would update both this and my other thread, in case someone else has these issues.

    Initially we had "check cut motor"...
  12. Motor Spins Briefly when Machine is Powered On - Stops Cutting After 5 Minutes

    My problem from a couple weeks ago was resolved with a new Xterm board....This is NEW.
    Ran 2 projects (9 hours) after the xboard was changed, all good.

    Now, the spindle turns for half a second...
  13. Replies
    2
    Views
    1,363

    Private Message Sent

    Private Message Sent
  14. Replies
    13
    Views
    5,113

    Thanks Al... Do you happen to have the...

    Thanks Al...
    Do you happen to have the "official" designations for the resistors too ?? I keep my parts labeled, as my color vision isnt as great as it once was....

    Brad
  15. Replies
    13
    Views
    5,113

    Ok.... -Dust collection IS grounded...metal duct...

    Ok....
    -Dust collection IS grounded...metal duct AND ground wire.
    -Shop is fully temp controlled, kept around 70.
    -We are always supervising when running the machine..work on the computer right...
  16. Replies
    13
    Views
    5,113

    Update - help !!

    UPDATE...HELP !!
    I know at this point that the X-termination board is bad. Upon removal, the board looked burnt and testing showed that three of the resistors were bad...maybe other things, but I...
  17. Replies
    13
    Views
    5,113

    RPM sensor meters fine, wires & connectionals all...

    RPM sensor meters fine, wires & connectionals all good. Motor seems to run fine at full speed when connected directly to a power source. The motor has been doing this a while, but once we get her...
  18. Replies
    13
    Views
    5,113

    On & Off RPM SENSOR or Something Else ??

    Machine does not spin the bit at startup on some occassions. The motor does kick in though, but just hear the hummmmm. Tap on the sensor, wiggle some wires and then it will run for a bit. Then,...
  19. **SOLD** 2" HDU 15# Precision Board - 5 Pieces, each 14" x 32" (2" thick)

    ******SOLD SOLD SOLD *****
    I have 5 pieces of Coastal Ent, 15# Precisionboard HDU in 2" thickness. This was leftover from a large project and is cut into CW convieniant 14" wide x 32" long.
    ...
  20. Ok...Heres an update for the future of mankind....

    Ok...Heres an update for the future of mankind.
    I added a thin piece of tubing as a spacer to the shaft on the bit we are measuring with (the one we have always used and it is at proper...
  21. The board(actually its HDU) is 2" thick. ...

    The board(actually its HDU) is 2" thick. Putting in as 2.000. This is a pattern that has been cut before(one yesterday actually), so that shouldnt be the issue. Also tried putting in a few...
  22. "Enter Board Thickness" Will Not Accept ANY Entered Number - HELP !!!

    I cut wide board all the time and nearly always have to enter the thickness manually. Today, I go to enter the thickness, as usual, and every time I enter the number and hit enter the machine just...
  23. Anyone have an Extra Roller Bearing Sweeper ?? To sell reasonable W/O $12 Shipping !

    Did a 250 hour bearing change and broke one pof my little sweepers.
    Anybody have ONE or two they would sell reasonable and send usps without the LHR $12 shipping fee ? LOL

    Brad
  24. Anyone have the Y & Z Truck bearing model numbers ?? Like NSK, to get them locally ?

    What are the model #s of the grooved bearings for the X&Y axis truck ??
    Brad
  25. Not sawdust...popped the seal off....just plum...

    Not sawdust...popped the seal off....just plum locked up. Anyone have an NSK or similiar number for all these Y & Z truck bearings where I could find them locally ??? Also the screw sizes ?? Might...
Results 1 to 25 of 60
Page 1 of 3 1 2 3