Search:

Type: Posts; User: want2b; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    3
    Views
    82

    Neat. I like the design of the pedestal in that...

    Neat. I like the design of the pedestal in that it is attractive while being simplistic. Have made some end tables and used turned 'posts' which created issues for me with the joints. Also like the...
  2. Replies
    3
    Views
    70

    Your best bet is to contact Carvewright at...

    Your best bet is to contact Carvewright at 713-473-6572. You will need the serial number located on the lower front on a plate below the feed tray. They will help you with registering your machine...
  3. Replies
    10
    Views
    203

    Looks great and obviously puts your cutoffs to...

    Looks great and obviously puts your cutoffs to good use at the same time.
  4. Replies
    2
    Views
    69

    Like it, especially how you inset the edge of the...

    Like it, especially how you inset the edge of the bottom shelf and undercut it to match the end panels. The ability to adapt to the occasional imperfection is what makes you a woodworker. I have...
  5. Replies
    5
    Views
    189

    Shame it didn't turn out as you wanted. I like...

    Shame it didn't turn out as you wanted. I like the design, especially the way the arms are accented by the channels making them seem independent while a part of the end. Could you add ends to the...
  6. Replies
    10
    Views
    203

    The variety in the bands looks great, haven't...

    The variety in the bands looks great, haven't done any of the boards yet. Sil has being doing them for all using colored epoxy pours with various woods.
  7. Replies
    10
    Views
    203

    Cool pattern for the board. How are you planning...

    Cool pattern for the board. How are you planning to finish it?
  8. Replies
    2
    Views
    248

    Astounding. Another one of the advances in...

    Astounding. Another one of the advances in technology that is wonderfully helpful and scary as all hell at the same time. Guess it's going to be up to the users state of mind and intentions as to...
  9. Good info, will use on my next book

    Good info, will use on my next book
  10. Your machine is set to Draft which will override...

    Your machine is set to Draft which will override any setting in the project. Turn it on and when you get the Project Menu press 0 and the configuration menu will appear and the first prompt which...
  11. Replies
    603
    Views
    235,173

    looks great, I didn't realize just how big it was...

    looks great, I didn't realize just how big it was going to turn out
  12. Replies
    603
    Views
    235,173

    OMG, really awesome. Let me know what company...

    OMG, really awesome. Let me know what company makes the material for your printer so I can buy some stock.
    Really, can't imagine waiting for the printer to finish something like that.
    The...
  13. Replies
    603
    Views
    235,173

    Tough day to make something applicable. Have to...

    Tough day to make something applicable. Have to agree the frame is unique. Just happy you keep thinking of items to contribute for those of us without your ability and passion for it.
    Can't count...
  14. Replies
    51
    Views
    62,106

    Sticky: Really great to see posts from new members. The...

    Really great to see posts from new members. The forum has been a lifeline link for many of us for a lot of years. There is a lot of information stored in the posts here and a few members who will...
  15. Replies
    261
    Views
    197,599

    Sticky: User issue. Either never knew or forgot about the...

    User issue. Either never knew or forgot about the Conform option(senor moment?). See the picture. When it is on the problem magically goes away. Only comes forward when working on text with...
  16. Replies
    261
    Views
    197,599

    Sticky: Centerline uneven

    Thought it must be me so I ran a carve and attached pic is the result. Both ends of the line are 'light'. Hard to even see the 'S' and in the center the Va are both scalped off. As noted above I do...
  17. Thx for the explanation

    Thx for the explanation
  18. Replies
    261
    Views
    197,599

    Sticky: Perfect timing. Set up for a quick carve on the...

    Perfect timing. Set up for a quick carve on the Happy with some text. Noticed the text was barely visible on the ends of the line of centerline. Have conforming vectors, guess some troubleshooting...
  19. Replies
    451
    Views
    193,151

    Xmas Ornament

    Modified Oscars' Tufted Titmouse into a cardinal with a little tool work after carving. Painted, twisted some wreath wire to make a loop, drilled a small hole in the back and inserted it with...
  20. Replies
    451
    Views
    193,151

    Wedding plaque

    Another one of the layered plagues. Managed to get this one done as a gift for a young couple about to tie the knot. Base wood is sycamore, mahogany last name and poplar first names.
  21. Replies
    3
    Views
    1,027

    Hoping 2024 is the best year ever for all! Be...

    Hoping 2024 is the best year ever for all! Be safe, be happy, enjoy what we have.
  22. Replies
    451
    Views
    193,151

    Didn't look at it as a two piece project , the...

    Didn't look at it as a two piece project , the channel then becomes simple. Only looked at the bend in the stem and wondering how to do it. Had experimented years ago with both smoking and making of...
  23. Thread: Merry christmas

    by want2b
    Replies
    6
    Views
    1,493

    My hope is that everyone has a great day enjoying...

    My hope is that everyone has a great day enjoying their friends and families. MERRY CHRISTMAS!!!!
  24. Replies
    451
    Views
    193,151

    Nice design. With a good finish it will be a...

    Nice design. With a good finish it will be a collectible. The biggest challenge I see is getting the hole from the lip to the chamber. Do you have a specific wood in mind?
  25. Replies
    451
    Views
    193,151

    I had done 2 spray coats of poly on these....

    I had done 2 spray coats of poly on these. Believe my worst mistake was not sanding the boards to fine finish grit first then the poly or lacquer. If I attempt something similar but smaller someday...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4