Search:

Type: Posts; User: keninar; Keyword(s):

Page 1 of 8 1 2 3 4

Search: Search took 0.00 seconds.

  1. Thread: Cutting board

    by keninar
    Replies
    8
    Views
    3,151

    I've used them both. My personal preference...

    I've used them both. My personal preference is......................................whatever color is available and what is on sale!! Hobby Lobby is not open on Sundays - and I usually encounter a...
  2. Thread: Cutting board

    by keninar
    Replies
    8
    Views
    3,151

    Very nice looking project. As to filling the...

    Very nice looking project. As to filling the carves, I've had good luck with a product known as Fimoclay (Hobby Lobby and Michaels). It's a clay based product that you work into the carves then...
  3. Replies
    3
    Views
    1,277

    Oramask procedure?

    Have seen a number of references to this product [Oramask] related to its use in protecting/painting letters, etc.

    As usual, when a project comes along the might benefit from it's use, I...
  4. Replies
    2
    Views
    1,432

    That's it! ThankS!!!!

    That's it!

    ThankS!!!!
  5. Replies
    2
    Views
    1,432

    Branch pattern?

    Seems as though I remember a pattern similar to the attached image being posted here not too long ago - but at my age, i cannot remember if I did........or merely dreamt it!

    This ring a bell with...
  6. Replies
    284
    Views
    165,308

    Thanks! Appreciate all your work - and patience!!

    Thanks! Appreciate all your work - and patience!!
  7. Replies
    284
    Views
    165,308

    After cleaning out my shop during the...

    After cleaning out my shop during the holidays.......and discovering how many sleds I've built over the years ----- I'm ready to go with the Universal Carrier.

    Have read the entire string of posts...
  8. Replies
    13
    Views
    12,998

    Oscar, Great job on the pattern! My...

    Oscar,
    Great job on the pattern!

    My father-in-law also served on a Balao class. ( Been married to his daughter for 36 years - this tidbit didn't come up until this past weekend - then comes...
  9. Replies
    9
    Views
    1,876

    Thanks for the response. Merry Christmas!!

    Thanks for the response.

    Merry Christmas!!
  10. Replies
    9
    Views
    1,876

    Can one set the machining order?

    Ran into an oddity this morning, perhaps the veterans of the group can enlighten me.
    Simple coaster project, one centerline letter and a circular cut.
    Centerline running a 60 degree bit
    Circular...
  11. Replies
    3
    Views
    1,141

    Thank you, Kindly! That did the trick. [I...

    Thank you, Kindly!
    That did the trick.
    [I knew there was an answer - I just wasn't experienced enough to figure it out]

    Thanks again!

    keninar
  12. Replies
    3
    Views
    1,141

    Setting lines to a specific angle

    Another quick question that I'm quite sure a quick answer exists - but cannot for the life of me see it.

    Using designer 1.187, can a draw a line and set it to an angle that is not an integer, i.e....
  13. Replies
    3
    Views
    1,838

    Assistance in getting pattern from a logo?

    Once again, I come Hat in Hand to the “Folks who can do what I can’t” – with a pattern request.

    Fielded a request to carve a college logo – image attached. I’ve erased the lettering – that I can...
  14. Replies
    7
    Views
    1,656

    Thanks for the input. Will check the local glass...

    Thanks for the input.
    Will check the local glass shops. Cope Plastics has a distribution center here, just not sure if they handle retails sales.

    Thanks!!

    keninar
  15. Replies
    7
    Views
    1,656

    Cast Acrylic for Edge Lit carvings/signs?

    Where do ya'll acquire clear cast acrylic? Was expecting to find it in the CW store, but realized they only offer white, translucent. (For lithopanes, I reckon)

    Any guidance greatly appreciated....
  16. Replies
    5
    Views
    2,454

    Gentlemen, Thank you, kindly, for your...

    Gentlemen,

    Thank you, kindly, for your efforts.

    Oscar - thanks for the roadmap. Haven't worked with blender yet, but perhaps this may be the impetus to do so.

    Played around a bit with...
  17. Replies
    5
    Views
    2,454

    Appreciate all the input! At work now, so can't...

    Appreciate all the input! At work now, so can't do much.

    Oscar, appreciate your efforts. Not familiar with your process - and don't have the software you reference. Thank you for taking a...
  18. Replies
    5
    Views
    2,454

    University Seal carveable?

    Fielded a query yesterday about carving a Georgetown University logo.

    Not quite sure where to start with this type of image.

    Is this doable - or do I let it lie?

    Image attached

    Thanks!
  19. Replies
    2
    Views
    1,773

    Once again, Sir: You da Man!! Awesome support...

    Once again, Sir: You da Man!!

    Awesome support on this forum.

    Thanks!

    keninar
  20. Replies
    2
    Views
    1,773

    Football via STL Importer?

    Don't have the STL importer - but can see the benefit of importing a 3D object, slicing it into 0.75 slabs, and reassembling.

    Has anyone done this with a football? Essentially creating a wooden...
  21. Replies
    2
    Views
    1,660

    Thank you, Kindly, Sir. Makes sense. Thanks!

    Thank you, Kindly, Sir.

    Makes sense.

    Thanks!
  22. Replies
    2
    Views
    1,660

    Inset on Select Bit?

    Afternoon All,

    Been away for a spell - trying to get back up to speed.

    Have a non-closed path that I would like to cut along with a .125 straight bit- but to preserve the desired dimension,...
  23. Replies
    8
    Views
    1,851

    Have noticed that, as I tend to use the...

    Have noticed that, as I tend to use the zero-depth carve quite often. With the letters having a height of 100, kinda expected the same result - but not so, hence the query.

    Thanks again!!

    So...
  24. Replies
    8
    Views
    1,851

    Makes perfect sense. Will give that a shot. Not...

    Makes perfect sense. Will give that a shot. Not critical on this carve, but would be nice to have up my sleeve next time I end up carving material where I want the surface to remain untouched.
    ...
  25. Replies
    8
    Views
    1,851

    Raster letters query

    When I design text in the Raster mode, it seems as though a slight, albeit very slight, amount of material is removed from the "surface" of the letters during the carving.

    Any way to leave the...
Results 1 to 25 of 183
Page 1 of 8 1 2 3 4