Search:

Type: Posts; User: want2b; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Thread: Produce sign

    by want2b
    Replies
    6
    Views
    153

    The sign is 11.5 by 43 , the speed limit is 55...

    The sign is 11.5 by 43 , the speed limit is 55 but most are running 65 and some push it to 70. Haven't seen a speeder stopped on it for several years. Seems most things like running red lights, etc...
  2. Replies
    16
    Views
    805

    Thank you for all your time and effort in making...

    Thank you for all your time and effort in making it happen, that is a huge gift .
  3. Replies
    8
    Views
    195

    Realized I had forgotten to set center on the...

    Realized I had forgotten to set center on the front and back , here is the corrected version. If you have already downloaded you can click on pattern and center both on the front and back. Deleted...
  4. Replies
    16
    Views
    805

    Same here, Thx

    Same here,
    Thx
  5. Thread: Produce sign

    by want2b
    Replies
    6
    Views
    153

    Thanks Jim, wanted to make it larger but was...

    Thanks Jim, wanted to make it larger but was given size limits, hopefully it will be visible from the road as it it going to be on a 4 lane rd where everybody is in a hurry
  6. Replies
    8
    Views
    195

    Had a little time so I decided to make the lure....

    Had a little time so I decided to make the lure. Made the two halves from a 3/4 board, worked out ok but found clamping the two pieces with glue was a challenge. The taper made the pieces want to...
  7. Thread: Produce sign

    by want2b
    Replies
    6
    Views
    153

    Produce sign

    Made a sign for a friend with a produce stand. Nothing fancy, two sided to place at an intersection nearby. Filled the letters with colored epoxy and finished with spar varnish hoping to protect it...
  8. Replies
    8
    Views
    195

    My thought would obviously be a two sided carve ....

    My thought would obviously be a two sided carve . Your 'width' should be ok for regular bits cutting it out from a 1.5 inch thick board. Not a fisherman but its size gives me a clue it isn't for...
  9. Replies
    16
    Views
    805

    Works for me, Thank you

    Works for me, Thank you
  10. Replies
    16
    Views
    805

    You have a PM, Rick H

    You have a PM, Rick H
  11. Replies
    477
    Views
    148,390

    That is going to be interesting to paint/finish....

    That is going to be interesting to paint/finish. Don't dare let my wife see this one. Looks great as always.
  12. Replies
    477
    Views
    148,390

    Panel looks great, made some interior bi-fold...

    Panel looks great, made some interior bi-fold window shutters years ago and did a single flower on them. First thing that popped in my head was these would really up the game. Who knows.. It was...
  13. Replies
    477
    Views
    148,390

    2nd eagle

    Finally got the next one done. Hopefully it does justice to the reason. My apologies to Oscar for making a couple of small tweaks in Corel to make it fit my perspectives.
    Thx again for the original
  14. Replies
    4
    Views
    445

    Agree with Mugsowner on the flex shaft test. On...

    Agree with Mugsowner on the flex shaft test. On the switches I believe the left switch gives the Close Lid message and the right switch controls the cut motor, not 100% sure. Can't remember the...
  15. Replies
    477
    Views
    148,390

    Looks like it would be great for a feathering...

    Looks like it would be great for a feathering situation. Definitely shows up in the pic, am curious if a carve would reflect the visual. Would be hard to shade the wood to give that open feathery...
  16. Replies
    477
    Views
    148,390

    Finished eagle

    Made time to try the eagle, really like it. Wife and I had a lot of discussion on the finish. Main issue was whether the stripes should go to the wing tips or be cut off to show some feathers and the...
  17. Replies
    477
    Views
    148,390

    Really like this one, kinda says it all Thanks

    Really like this one, kinda says it all
    Thanks
  18. Replies
    21
    Views
    972

    Love the eagle, will be using it. I know I would...

    Love the eagle, will be using it. I know I would love to closer to Mugsowner for the poplar, guess I'd need a sawmill but that could be cheaper than years of buying wood.
    Hope you both have a great...
  19. Thread: tracking issue

    by want2b
    Replies
    5
    Views
    346

    Good thing to check. Have had problems with...

    Good thing to check. Have had problems with bowing of the board from end to end causing tracking errors. Any small 'dip' going over the tracking wheel can caude either a small shift in the pattern or...
  20. Don't have answers for all your issues. I've...

    Don't have answers for all your issues. I've used three dust collectors and all leave some dust, the carvewright model is my least favorite. I have started placing some masking/blue tape over any...
  21. Thread: tracking issue

    by want2b
    Replies
    5
    Views
    346

    I agree with Mugsowner . Had a tracking issue...

    I agree with Mugsowner . Had a tracking issue myself and replaced the roller assembly. Took the old unit apart and found it full of fine dust. You might try cleaning yours.
  22. Replies
    2
    Views
    420

    Looks like you've found an answer for the need of...

    Looks like you've found an answer for the need of a convenient charging place. Not sure if Android has the technology either but it is an obvious fix for those that need one. Shows what thinking out...
  23. Thread: Floor project

    by want2b
    Replies
    3
    Views
    250

    Thanks Jim, wife and I are tickled with the...

    Thanks Jim, wife and I are tickled with the result. Appreciate the feedback, we have had that same discussion. I wasn't explicit when I said doorway. Should have said set back from but in line with...
  24. Thread: Floor project

    by want2b
    Replies
    3
    Views
    250

    Floor project

    Latest project is a beauty salon for my daughter-in-law in a pole barn at their house. Got the idea it would be neat to personalize the floor so I carved the business name into a piece of the vinyl...
  25. Replies
    21
    Views
    972

    That is so cool. I can see how the printer would...

    That is so cool. I can see how the printer would be such a draw. You get to use your imagination in the conception, design it in the software, and then get to see the physical product in full 3D...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4