Search:

Type: Posts; User: FWMiller; Keyword(s):

Page 1 of 15 1 2 3 4

Search: Search took 0.00 seconds.

  1. Thread: Name signs

    by FWMiller
    Replies
    4
    Views
    1,981

    Name signs

    We've had a tradition of making end of year gifts for my girls teachers. I cut them out on the carvewright and the girls paint them. This year my board sensor crapped out as I was carving only the...
  2. Replies
    17
    Views
    6,084

    I use a craftsman shop vac and have very little...

    I use a craftsman shop vac and have very little dust left overa long as the filter is clean. Seems like you may have an air flow issue. I have found that my board sensor can sometimes be finicky too...
  3. Replies
    5
    Views
    1,659

    It's dead. But fortunately for me Henry was kind...

    It's dead. But fortunately for me Henry was kind enough to go out of his way to ship me one.

    Sent from my SM-G920V using Tapatalk
  4. Replies
    5
    Views
    1,659

    Hello. Thought I'd post again to see if anyone...

    Hello. Thought I'd post again to see if anyone else has a board sensor, new or used, that they're willing to sell. Being in Canada it's a big hassle for Henry to ship to CA. Unfortunately LHR...
  5. Replies
    5
    Views
    1,659

    Need a Board Sensor

    Hello,

    I'm in need of a board sensor. Does anyone have a board sensor they are willing to sell? New or used is fine.

    Thanks,

    Frederick
  6. Replies
    9
    Views
    1,893

    It could potentially be impacted by the board if...

    It could potentially be impacted by the board if it's not flat along the edge where the brass roller contacts the board. If you're not sure you can try to measure a piece of flat plywood.

    Sent...
  7. Replies
    23
    Views
    13,911

    Dovetails were invented long before glue. If they...

    Dovetails were invented long before glue. If they fit that tight without glue they should be fine.

    Sent from my SM-G920V using Tapatalk
  8. Thread: Drill Tool

    by FWMiller
    Replies
    6
    Views
    1,660

    My observation is that this is not true. It seems...

    My observation is that this is not true. It seems to select the order based on position on the board to minimize the x travel. When you route a connected line it does it in the direction that the...
  9. Replies
    1
    Views
    1,023

    Memory card reader

    Anyone have an extra used memory card reader they are willing to sell? I recently moved and can't find my card reader amongst boxes and boxes of stuff. Went to look at ordering a new one a found they...
  10. Replies
    6
    Views
    3,899

    Yes, Correct.

    Yes, Correct.
  11. Replies
    6
    Views
    3,899

    If your machine malfunctions on every other...

    If your machine malfunctions on every other project, it might be because you don't have good dust collection.
  12. Replies
    162
    Views
    95,108

    Good point. RPM is a lot higher than drill press...

    Good point. RPM is a lot higher than drill press but if there's no side force it makes sense. I guess you just need a good bit that the flutes don't get clogged easily which is often a problem with...
  13. Replies
    162
    Views
    95,108

    Where do you find a 1/16 end mill with more than...

    Where do you find a 1/16 end mill with more than 1/4 inch cut length?
  14. Replies
    14
    Views
    5,851

    Would be nice if the website could actually...

    Would be nice if the website could actually distinguish between out of stock and discontinued.
  15. Replies
    42
    Views
    9,820

    I've had no problems on Windows 10 so far with...

    I've had no problems on Windows 10 so far with designer 3. So far Windows 10 has run everything I ever used on Windows 7 with no problems.
  16. I'm very happy with the rubber belts. Not a...

    I'm very happy with the rubber belts. Not a mandatory upgrade but well worth the expense when you've already got so much money in the machine already. Essentially no maintenance which the CW is worth...
  17. Thread: RPM sensor

    by FWMiller
    Replies
    29
    Views
    5,422

    I used to get it all the time, regardless of...

    I used to get it all the time, regardless of shutting down the machine or not. Over the past six months I've done a lot of vector carves that used to cause the problem a lot and have not had a single...
  18. Thread: RPM sensor

    by FWMiller
    Replies
    29
    Views
    5,422

    There's nothing you can do to get rid of this...

    There's nothing you can do to get rid of this problem, other than being lucky it goes away or doesn't show up. It's a bug in the firmware design that seems to be dependent on performance...
  19. Thread: RPM sensor

    by FWMiller
    Replies
    29
    Views
    5,422

    I'll just chalk it up to luck then. I'll take any...

    I'll just chalk it up to luck then. I'll take any luck I can get with the machine.
  20. Thread: RPM sensor

    by FWMiller
    Replies
    29
    Views
    5,422

    I used to have that problem a lot but have not...

    I used to have that problem a lot but have not seen it in a long time. I replaced my power supply a while back with a newer version C power supply and think that may have something to do with it.
  21. Thread: musslechuck

    by FWMiller
    Replies
    15
    Views
    3,657

    AL, has the bit length issue been solved in the...

    AL, has the bit length issue been solved in the latest version of designer? I use a CT with the ER-11 adaptor for my 1/8 cutting bits. I've put them in the bit holder at a wide variety range of...
  22. Replies
    3
    Views
    12,685

    To answer your question about the board settings...

    To answer your question about the board settings menu, it only shows what the selected raster bit is. There is no other window where you can see a list of all bits used on your design like straight...
  23. Replies
    7
    Views
    1,957

    Double sided tape might be too much to hold the...

    Double sided tape might be too much to hold the veneer down and then release it safely. And the upcut action of the bit is going to want to lift the veneer and without rigid support on top it could...
  24. Replies
    6
    Views
    2,063

    You can do it using a sled.

    You can do it using a sled.
  25. Thread: Carving bit

    by FWMiller
    Replies
    8
    Views
    2,039

    If the touch point is more than about a quarter...

    If the touch point is more than about a quarter of an inch lower than the max height of the board you will get stuck in this loop. I've only run into this problem when I used a sled which had sides...
Results 1 to 25 of 355
Page 1 of 15 1 2 3 4