Search:

Type: Posts; User: Mugsowner; Keyword(s):

Page 1 of 19 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    5
    Views
    260

    I do not have any issues at all. This is just of...

    I do not have any issues at all. This is just of bit of info I picked up here, where others have mentioned issues that may have been caused by the lighting. Not saying you will have problems, but...
  2. Replies
    5
    Views
    260

    Led lighting is great and easy to work with....

    Led lighting is great and easy to work with. Being low voltage the issues of shock go away. The intense light from led tends to mess with the measuring process, so it would need to be shut down for...
  3. I thought I would try to make a tabletop model. I...

    I thought I would try to make a tabletop model. I think the dowel that is needed is 1 inch dia. about 4 inches long not adding for recessed amount.
  4. There is a table top design out there as well....

    There is a table top design out there as well. Same design, but just a disc with a full circle cove.
  5. Great job Oscar, not to beat up on the design, as...

    Great job Oscar, not to beat up on the design, as it does seem to have most of what is needed and I can not open the mpc to view, so I am going off the pictures uploaded. The recessed ring should be...
  6. Replies
    15
    Views
    15,234

    See If this works for you.87708

    See If this works for you.87708
  7. Replies
    11
    Views
    612

    Wow, this really shows the skills and imagination...

    Wow, this really shows the skills and imagination you have. Your project looks great and shows the workmanship that had to be exercised. Great job
  8. Replies
    18
    Views
    1,530

    I did some looking around to see if I could find...

    I did some looking around to see if I could find a answer for you. This is what I found. Extruded has higher tolerances and if thickness checked should be with in .05, where cast can be as far off as...
  9. Replies
    198
    Views
    17,563

    Nice work Oscar

    Nice work Oscar
  10. Replies
    1
    Views
    295

    Evening glad to see people do still lurk out...

    Evening glad to see people do still lurk out there. not sure if this will help or not, but here it goes. When you want to move a single line there should be a hand type cursor for selecting. When...
  11. Replies
    4
    Views
    729

    Happy memorial day

    Just wanted to stop in and wish everyone a happy Memorial day and weekend. Stay safe and enjoy.
  12. Replies
    576
    Views
    85,786

    Sticky: Welcome Jeffery, Hope the machine preforms well...

    Welcome Jeffery, Hope the machine preforms well for you. The Carvetite spindle is an upgrade, however the sand paper belts are not. They work, but do tend to slip now and then. There is a few points...
  13. Replies
    2
    Views
    311

    Put the tape in a T shape. One across where the...

    Put the tape in a T shape. One across where the sensor measures width then again where the sensor looks for the the edge of board.
  14. This should work. Bring it in outline it then...

    This should work. Bring it in outline it then delete the ptn.
  15. Replies
    3
    Views
    247

    Wd-40 will not hurt the bearings. Pop the dust...

    Wd-40 will not hurt the bearings. Pop the dust covers off the bearings. You will be able to see which ones are rolling and which ones don't. Yes they do have loctite on the bearing screws of the high...
  16. Replies
    198
    Views
    17,563

    Great work Oscar, I'm sure they will be enjoyed.

    Great work Oscar, I'm sure they will be enjoyed.
  17. Replies
    10
    Views
    705

    I saw a power supply for sale on ebay...

    I saw a power supply for sale on ebay https://www.ebay.com/itm/163615668390?ul_noapp=true
  18. Replies
    1
    Views
    228

    This may work for you.

    This may work for you.
  19. Replies
    7
    Views
    454

    This would depend on which bit you are using and...

    This would depend on which bit you are using and the type of carving (raster or vector). Not knowing for sure, but thinking the board moves along the X axis at about .015 per pass of the 1/16"...
  20. Replies
    312
    Views
    27,790

    Wow seeing them photos, you do have your work cut...

    Wow seeing them photos, you do have your work cut out for you. Very impressive.
  21. Replies
    312
    Views
    27,790

    Good luck in the contest, hope you at least...

    Good luck in the contest, hope you at least place. Neat design
  22. Replies
    13
    Views
    706

    This may be what your looking for....

    This may be what your looking for....
  23. Replies
    13
    Views
    706

    Yes, the 1/32 bit will give finer detail, but you...

    Yes, the 1/32 bit will give finer detail, but you need Designer Pro 3 to use it.
  24. Replies
    7
    Views
    506

    I use jog to center on a few of my projects. I...

    I use jog to center on a few of my projects. I have some small cut outs that I use it steady as it allows me to make multiple cut outs on the same board at different times. I noticed that the truck...
  25. Replies
    312
    Views
    27,790

    Wild looking

    Wild looking
Results 1 to 25 of 474
Page 1 of 19 1 2 3 4