Search:

Type: Posts; User: Mugsowner; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    322
    Views
    30,179

    Looks sharp Oscar

    Looks sharp Oscar
  2. Replies
    2
    Views
    180

    What would be shipping to 54130 for the 8x10's?

    What would be shipping to 54130 for the 8x10's?
  3. Replies
    10
    Views
    269

    Cutting is a sharp flat nose, and carving is a...

    Cutting is a sharp flat nose, and carving is a curved/angled point, right?? Right
    Did I have a wrong bit in the machine at some point and it remembers that measurement? No
    And wants to see...
  4. Replies
    6
    Views
    263

    The switch on the left side is for the cover,...

    The switch on the left side is for the cover, the switch on the right is for the motor.
  5. Replies
    3
    Views
    139

    Try going to your carve list and clicking on it...

    Try going to your carve list and clicking on it there. I have seen this before and that is ow I get around it.
  6. Replies
    3
    Views
    190

    Happy New Year

    I would like to wish all of you and your fiends and families a Happy New Year. Hope it is a good one.
  7. Replies
    589
    Views
    88,288

    Sticky: Welcome Dave, sorry to hear you are having card...

    Welcome Dave, sorry to hear you are having card issues. A while back cards were chatted about and one of the ideas that came up was to put a piece of tape on the cards to make them easier to remove...
  8. Replies
    7
    Views
    317

    As for the picture you could run through some...

    As for the picture you could run through some photo software to clean up. When you use a vector, you will have to select a bit, in this step you will be asked to select depth of cut.
  9. Replies
    3
    Views
    178

    I to would like to wish all of you and yours a...

    I to would like to wish all of you and yours a very Merry Christmas!
  10. Replies
    6
    Views
    380

    I would agree with Al the epoxy repair would be...

    I would agree with Al the epoxy repair would be much stronger.
  11. Replies
    6
    Views
    380

    Nice job on the repair. The tywraps may give you...

    Nice job on the repair. The tywraps may give you an issue, but I do not think they will not. The strength you added to the cable housing holding power is huge. Not sure if repair would hold without...
  12. Thread: Trinket box

    by Mugsowner
    Replies
    17
    Views
    756

    Hello Oscar, the design is great. I think a...

    Hello Oscar, the design is great. I think a trinket box with a delicate nature should have a shallow carving applied to accent the box. Deeper carving seem to aggressive to me for delicate projects....
  13. Today I think is my last day with internet. There...

    Today I think is my last day with internet. There is no internet where I spending the next two weeks or so.
  14. I have a motor that brunt out on me. I could...

    I have a motor that brunt out on me. I could remove the casing. The problem I have is I will not be near the motor for a couple weeks. I will be back the first week in December.
  15. Replies
    4
    Views
    254

    I have an old motor here that I can view the...

    I have an old motor here that I can view the cable end. What I see is just a square opening on the end, but I think there is a ridge where the square stops. The square looks to be a threaded insert,...
  16. Replies
    4
    Views
    254

    This could be the same issue. The cable may that...

    This could be the same issue. The cable may that a broken wire which is rubbing the sheath and causing the run up to be hampered a bit, causing the message. I would check the brushes to make sure...
  17. Replies
    10
    Views
    469

    When you load the carving bit, place a shim on...

    When you load the carving bit, place a shim on the keyboard edge of the board. The board does not move while finding bit and surface. After the machine goes thru the bit finding you can hit the stop...
  18. Replies
    63
    Views
    2,511

    Yes the clutch is behind the handle. There are...

    Yes the clutch is behind the handle. There are shims behind the handle. They are between the handle and spring and are used to push the spring forward putting pressure on the crank torque plate. The...
  19. Replies
    63
    Views
    2,511

    Low head pressure could be caused by the clutch...

    Low head pressure could be caused by the clutch releasing early, in which case you would have to shim to increase pressure.
  20. Replies
    4
    Views
    654

    These machines can be purchased with issues...

    These machines can be purchased with issues fairly cheap. All of mine were purchased used.One first was carving all over the place, looked closer, I found a cracked Z truck frame. Ordered a new Z...
  21. Replies
    12
    Views
    890

    I do the same as Jerry to a point. My jig is...

    I do the same as Jerry to a point. My jig is mounted to one of my routers. It is a piece of poly carbonate with an edge guide mounted to it. The edge guide is mounted 3/4" off bit center. Any other...
  22. Replies
    12
    Views
    890

    Yes the keyhole function is an add on that needs...

    Yes the keyhole function is an add on that needs to be purchased. The cost is around 50 dollars and comes with a bit, I believe. A new bit would run you about 30 dollars, so with the bit it is a...
  23. Replies
    5
    Views
    561

    Get bit of info. Enjoy the fact that I can view...

    Get bit of info. Enjoy the fact that I can view the inside of the programmer without tearing it apart. I always dread the first opening of any item I have never worked with or seen worked on.
  24. Replies
    3
    Views
    324

    Tablerock I sent you a private message

    Tablerock I sent you a private message
  25. Replies
    6
    Views
    549

    I do not have any issues at all. This is just of...

    I do not have any issues at all. This is just of bit of info I picked up here, where others have mentioned issues that may have been caused by the lighting. Not saying you will have problems, but...
Results 1 to 25 of 498
Page 1 of 20 1 2 3 4